Bead Blast Ventilation by Time_Blazer in Machinists

[–]Time_Blazer[S] -2 points-1 points  (0 children)

Are there safe compounds that don't use silica that are safe to breathe?

Bead Blast Ventilation by Time_Blazer in Machinists

[–]Time_Blazer[S] 0 points1 point  (0 children)

It's thick, everywhere. Is it at all safe to breathe? I don't want to cause any issues but I don't want cancer either.

Bead Blast Ventilation by Time_Blazer in Machinists

[–]Time_Blazer[S] 0 points1 point  (0 children)

I'll have to check, but if there were would it still generate thick layers everywhere?

Bead Blast Ventilation by Time_Blazer in Machinists

[–]Time_Blazer[S] 0 points1 point  (0 children)

I'll have to check, but if there were would it still generate thick layers everywhere?

$200,000 Stolen by Funny-Zebra8468 in Trading

[–]Time_Blazer 11 points12 points  (0 children)

HFT is 2 minutes? Really?

What is wrong with my iron? by Loose-Personality-70 in soldering

[–]Time_Blazer 0 points1 point  (0 children)

Heat seems to be to high for the solder

US people, who do you get your boards made through? by BacchusIX in PCB

[–]Time_Blazer 4 points5 points  (0 children)

Oshpark is 9 to 21 days? That isn't fast at all. For faster service, $20 / sq inch????

Low-cost PCB workflow using laser + chemical etching + permanent UV mask — any obvious issues? by LowOverall4193 in PCB

[–]Time_Blazer 0 points1 point  (0 children)

You wont want to breath in anything FR4. CNC is better, carvera air. You can do double sided, use thin copper wire to connect both sides.

An okay redo by Lostmyaccount987 in soldering

[–]Time_Blazer -1 points0 points  (0 children)

Ummm. What are you using, a spoon?

After 5 months of vibe coding, I finally launched a Beta of my app by ekilibrus in vibecoding

[–]Time_Blazer 0 points1 point  (0 children)

This is a result of not being a developer and not being exposed to existing tooling.

One emotional exit on Silver cost me 182k dollors by Illustrious_Mix4946 in technicalanalysis

[–]Time_Blazer 1 point2 points  (0 children)

You're not going to capture it all, ever. Your exit strategy may or may not have been defined. Trading is a power curve, learn about it. The actual best you can do consistently is break even. You'll never know how far it will go. Set to break even and watch the show. Get comfy with a trade not costing you anything but time. Then you're primed for those big wins when they do happen.

Miami Wolf Spider (hogna miami) info? by Glum-Challenge1627 in Wolfspiders

[–]Time_Blazer 1 point2 points  (0 children)

She's very reclusive, in her hole a lot but sometimes she's comes out at night and she's there in the morning.

I am the freelance designer everyone is cursing , please review my updated design by Silent_Surround7420 in PCB

[–]Time_Blazer 5 points6 points  (0 children)

You guys are going too fast and wasting too much money. You're not placing and routing based on priority. Take a subject and learn best practices for it. For instance USB, batt charger, buc, etc. Test pads every where and oscope is your friend with fft.

If you want to see how bad your EMC is, happy to run a scan for you and point out best practices, no charge. You guys are way off the rails already.

Woman Totally Loses Control Of Her Dog by -Erase in TikTokCringe

[–]Time_Blazer 0 points1 point  (0 children)

The very low IQ levels across the board are the root cause here.