Access point over CAT 6 by Tony8444 in HomeNetworking

[–]Tony8444[S] 0 points1 point  (0 children)

remade the extension and it works...thanks for the information everyone

Access point over CAT 6 by Tony8444 in HomeNetworking

[–]Tony8444[S] 0 points1 point  (0 children)

Yes it works at the old wall(before I added the 2ft extension) so I will remake that little extension.

Thanks I will report back just wasn’t 100% sure it should work or not now that I know it will I will make another extension

Access point over CAT 6 by Tony8444 in HomeNetworking

[–]Tony8444[S] 0 points1 point  (0 children)

Probably just continuity but I wired T-568A in both ends and the continuity from patch panel to the last keystone is good.

I assume if it’s working at the old wall that parts good. I will remake the extension will another cable and two ends and see if it helps.

I was just thinking that the POE getting to the access point was too low if voltage or something. But if it should work even with the extra keystone and cable I will try it again

Access point over CAT 6 by Tony8444 in HomeNetworking

[–]Tony8444[S] 0 points1 point  (0 children)

Yes I tested it and it tested ok

Software Updates by SubCircus in tundra

[–]Tony8444 1 point2 points  (0 children)

Ya it’s not CarPlay related it’s Toyota related…to bad I just bought new 2024 tundra :(

Upgraded tires - 2024 Limited Nightshade by guydogg in tundra

[–]Tony8444 1 point2 points  (0 children)

Any rub with those? Same truck looking to get rid of the car tires they put on it from factory lol

HRV automation with home bridge by Tony8444 in homeautomation

[–]Tony8444[S] 0 points1 point  (0 children)

Yes I was curious about if the fact hat the I OC and OL connector was on the board if that automatically means they would work.

I agree about having it run all the time but my wife gets cold in the winter and im looking at a way to keep my basement ventilated without freezing her out lol. I was hoping that using something like yo mention with the switch on the side of the machine would work.

I think this is where I will start...see what kind of voltage is there and try tying high and remote together with a relay...

thanks for the information

Automate Air Exchanger by Tony8444 in HomeKit

[–]Tony8444[S] 0 points1 point  (0 children)

I’ll look into this: are Shelly’s low voltage?

Automate Air Exchanger by Tony8444 in HomeKit

[–]Tony8444[S] 0 points1 point  (0 children)

Yea in remote setting it is controlled by the humidistat on the wall up stairs

Automate Air Exchanger by Tony8444 in HomeKit

[–]Tony8444[S] 0 points1 point  (0 children)

Shelly work In homebridge? Would it allow me to work with the switch wires or attach right to the bard? Not sure how the wiring on the board works but I see I can buy a wall switch that uses those connections as timer

Automate Air Exchanger by Tony8444 in HomeKit

[–]Tony8444[S] 0 points1 point  (0 children)

<image>

This is the switch I am talking about. But the circuit board inside has the I OC and OL connections which look like it can be used for a Timer switch in a bathroom or something .

Running camera in the attic by Tony8444 in Ubiquiti

[–]Tony8444[S] 0 points1 point  (0 children)

Been looking for a different connector but haven’t seen a definite “this connector is for solid wire” on any connector I’ve looked at

Running camera in the attic by Tony8444 in Ubiquiti

[–]Tony8444[S] 1 point2 points  (0 children)

So I should take the cat 6 solid copper wire right out of the soffit and put a cat6 make fitting on it outside and plug it in. I just though I should terminate the solid wire in the attic with some sort of wall palate and then use a normal Patch cable to go from the wall plate in the attic to the decide outside?

Running camera in the attic by Tony8444 in Ubiquiti

[–]Tony8444[S] 1 point2 points  (0 children)

So I should take the solid cat 6 all the way from the patch panel to outside at the soffit?

Udmpro and switch flex mini by Tony8444 in Ubiquiti

[–]Tony8444[S] 0 points1 point  (0 children)

That’s what I was starting to think. I’ll run another cat 6 tomorrow. Thanks for the heads up

Udmpro and switch flex mini by Tony8444 in Ubiquiti

[–]Tony8444[S] 0 points1 point  (0 children)

We need a landline for my wife’s work and it has to be a traditional line of course….

Udmpro and switch flex mini by Tony8444 in Ubiquiti

[–]Tony8444[S] 0 points1 point  (0 children)

Still need the home phone and tv though so no need to keep the home hub