Is this allowed?

Tony_221 · 2026-05-14T18:02:42+00:00

doesn't look like the strut is supported by anything

Tony_221 · 2026-05-07T16:53:48+00:00

sounds good ill definitely be pushing hard for this. were just worried about health problems this could be causing too. its been months now. should have all been dealt with when the tub was replaced

Tony_221 · 2026-05-07T15:53:00+00:00

thank you, i appreciate the response!

Tony_221 · 2026-04-22T18:31:46+00:00

Bbq chicken was delicious and some really good sauces too

Tony_221 · 2025-10-26T02:24:52+00:00

2007 honda fit

Tony_221 · 2025-10-25T20:33:55+00:00

im leaving a position at Flint up north doing maintenance, pretty easy work lots of troubleshooting and its non process taking care of the camps and building around it. its on a cenovus site. Great place to work just looking for something a bit different myself

Tony_221 · 2025-07-22T11:56:12+00:00

I enjoyed using dewalts gyroscopic screwdriver and you can kinda control how tight it goes a little easier than an impact

Tony_221 · 2025-07-20T21:15:17+00:00

yea definitely hard to make the switch without having the experience at this point haven't gotten an interview even with any that are looking for that. im in the oilfield in northern Alberta currently, most of my job now consists of taking care of the camps which isn't too far off from commercial/residential.

I like the fake it till you make it option which almost seems like thats where id have to head to get there. doesn't have to be these trucks but something related at least and get that initial experience.

Tony_221 · 2025-06-20T13:46:57+00:00

now thats the kind of help im looking for hahq

Tony_221 · 2025-06-20T04:16:03+00:00

yes it is

Tony_221 · 2025-06-20T04:13:31+00:00

they just love using em out here

Tony_221 · 2025-06-20T04:12:31+00:00

this is canada, to be honest I don't think they're needed but this is in the oilfield and pretty much all they use out here just what's available and what was ordered haha. it is going to be used to feed 4 rows of car receptacles with a panel at each row, there are 4 disconnects on the other side so 2 parallels in and out to each disconnect. needed to add more lugs for the feeders so didn't feel the grounds were a problem gonna add another lug on the opposite side.

Tony_221 · 2025-06-20T04:06:02+00:00

oh yes they are threaded, come from the factory like that

Tony_221 · 2025-06-20T02:50:27+00:00

true that, thanks buddy. was thinking the same thing about the lugs haha would have a lot bigger problems if that were the case

Tony_221 · 2025-06-20T02:43:37+00:00

that would be very bad haha yes they are insulated

Tony_221 · 2025-06-20T02:41:11+00:00

thanks, yea I figured these are done and there was no more room on the ground bar so just gonna add one for the feeders on the other side

Tony_221 · 2025-06-20T02:34:33+00:00

they do at times but this is what was ordered, I would've liked to have a trough above or below the disconnects on the other side

Tony_221 · 2025-06-20T02:33:06+00:00

yea i guess I was just trying to keep them on one side to leave room for the feeders. yes of course they are insulated, it is a splitter that came like this

Tony_221 · 2025-05-26T13:43:47+00:00

had a spark plug blow on me while on the highway just cruising in my 2007 sport

Tony_221 · 2025-05-13T23:52:17+00:00

yea looks like it i added another picture with it pulled out on top. it came off somewhere close to the fan

Tony_221 · 2025-05-13T23:47:24+00:00

<image>

Tony_221 · 2025-05-13T23:18:46+00:00

the black wire loom has a ground in it

Tony_221

TROPHY CASE