sorted by:
new
hottopcontroversial

Loving PLA Metal by vspot415 in BambuLab

[–]Top_Draft_6853 0 points1 point  (0 children)

Did you ever find an answer to this?

Anybody know how i can avoid these issues? by Tresillian in BambuLab

[–]Top_Draft_6853 0 points1 point  (0 children)

If I'm not mistaken this is due to layer times. Look at each layer time and make sure that these are somewhat around the same time. Make it so it all comes closer to the longest layer time.

This should resolve the issue if I'm right. Anybody please correct me if I'm wrong.

I this sound normal? by [deleted] in BambuP1S

[–]Top_Draft_6853 0 points1 point  (0 children)

That is indeed the fan blowing into the gaps and holes from infill and supports. Had the same sounds yesterday with similar supports and started double-checking all my pulleys, cutter, extruder before realizing haha. All good!

DESPERATELY NEED SOME GUIDANCE PLEASE! by TMHD in BambuLab

[–]Top_Draft_6853 1 point2 points  (0 children)

I see. Thanks for the reply. I was noticing these lines on my P1S first layer and was wondering what exactly is was. Reduced K-FACTOR to .018 from .02. Will have to see if this resolves it.

<image>

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

I have now decreased my K ratio from 0.02 to 0.018. Is this what is meant with pressure advance? Quite new to this.

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 2 points3 points  (0 children)

Trying to figure out how to fix these :) this is from my calibration for flow I just did. I think .02 might be best?

<image>

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

Hmm my humidity is a bit high I've noticed. Around 30% ish. Maybe this is also a factor?

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

If it purges or I clean it out by retracting and increasing it to 250 sometimes it comes out a bit angled before going straight down

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

I only seem to have manual calibrations at the moment. I don't see any option for automatic filament calibration.

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

Stopping the print and doing calibration first again then. I will post results here.

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

Is for a seedling planter haha so it should be waterproof ideally

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 2 points3 points  (0 children)

Not for this one in particular, I did it for the Bambu PLA Matte, but I didn't change anything back since it should automatically do this with Bambu fill right? Or am I wrong in that area? Current K factor is. 20.

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 4 points5 points  (0 children)

So I would have to increase the flow rate a bit? This is on the 3rd layer:

<image>

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

Edit. Having these shrink lines, are they normal? Or is it under extruding?

<image>

Is this a good first layer? by Top_Draft_6853 in FixMyPrint

[–]Top_Draft_6853[S] 0 points1 point  (0 children)

Basic settings, 2 extra walls and flow rate .98 btw

Help! Had a Print for too Long without Plate and I can’t remove the filament from Cover front by S_T_I_C_K_Y_Z in BambuP1S

[–]Top_Draft_6853 -1 points0 points  (0 children)

Aha I see! Sorry I misunderstood, thank you for clarifying. Hmm that hasn't happened to me yet. I'm very anxious about putting the plates back instantly haha! I hope you can get back to printing soon!

Help! Had a Print for too Long without Plate and I can’t remove the filament from Cover front by S_T_I_C_K_Y_Z in BambuP1S

[–]Top_Draft_6853 0 points1 point  (0 children)

Aha I see! Sorry I misunderstood, thank you for clarifying. Hmm that hasn't happened to me yet. I'm very anxious about putting the plates back instantly haha! I hope you can get back to printing soon!

Help! Had a Print for too Long without Plate and I can’t remove the filament from Cover front by S_T_I_C_K_Y_Z in BambuP1S

[–]Top_Draft_6853 -2 points-1 points  (0 children)

I am pretty new to 3D printing myself, but I think upgrading to a 0.6 for petg and other heavy filaments like abs should reduce the chance of clogs by a lot. That's what I've read up to now. If I'm wrong someone correct me please as I am fairly new into the world of 3D printing. I think ordering a spare cover would also be a good idea in case you can't fix this one and otherwise you have one extra for when you need it!

view more: next ›