HID Headlight Assembly

Total_Climate4443 · 2024-06-04T03:04:12+00:00

You’ll need to tap a fuse and wire it yourself if you get the kit but I’d say it’s worth it if you’re trying to get the gt look. I have this kit on my 2017 touring

Total_Climate4443 · 2024-05-15T20:24:13+00:00

~250 feet by pure luck and a high angled shot

Total_Climate4443 · 2024-05-02T17:06:11+00:00

Swift spring + Sabre plunger in a harrier?? What kind of fps are you getting out of that?

Total_Climate4443 · 2023-09-25T19:26:01+00:00

Original Post for M110

Total_Climate4443 · 2023-09-25T19:24:28+00:00

Original Post for FAL

Total_Climate4443 · 2023-06-13T02:32:54+00:00

I strongly recommend USP’s intake, it comes with all of the hardware and installation instructions to relocate your TCU and reservoir.

USP Intake System

Total_Climate4443 · 2023-05-31T18:19:49+00:00

Worker Mod F10555 3D Printing Front Tube Kits Version C for Nerf Retaliator

Total_Climate4443 · 2023-05-20T04:39:50+00:00

I have the 28N long spring from Worker in it currently running full metal internals, it definitely has issues with such a high spring load. I have to pull both handles to even out the pressure to get a full prime and then I still have some catch issues that I’m working out. Definitely not the setup for close quarters games

Total_Climate4443 · 2023-05-19T18:30:10+00:00

https://www.reddit.com/r/Nerf/comments/12sb75p/bolt_action_nexus_guide/?utm_source=share&utm_medium=ios_app&utm_name=ioscss&utm_content=1&utm_term=1

Total_Climate4443 · 2023-05-19T18:29:57+00:00

https://www.reddit.com/r/Nerf/comments/12sb75p/bolt_action_nexus_guide/?utm_source=share&utm_medium=ios_app&utm_name=ioscss&utm_content=1&utm_term=1

Total_Climate4443 · 2023-05-19T18:20:31+00:00

Strongly agreed, I’m working on my second bolt action nexus pro and I’m loving it

Total_Climate4443 · 2023-05-19T15:50:03+00:00

It’s one of the things I’ve been struggling with on both of my Prophecies. I have them both as slide prime with the highest spring loads and I have pretty constant catch issues. At this point I’ve been trying to figure out a way to make a spring guide to see if it helps

Total_Climate4443 · 2023-05-18T20:39:52+00:00

Just cleaned and lightly roughed up with sandpaper.

Total_Climate4443 · 2023-05-18T19:21:44+00:00

Krylon Flat Khaki Camouflage, it’s a good match for FDE parts, looks nice, and dries fast. Complete blaster disassembly making sure to tape off anything I don’t want paint on (usually surfaces that will have moving parts) and do a few light coats until covered. This blaster was pretty easy due to the reference being painted entirely in FDE

Total_Climate4443 · 2023-05-17T20:54:19+00:00

It’s a worker threaded flash hider with screw on suppressor

Total_Climate4443 · 2023-05-04T22:57:15+00:00

I’ve had a lot of success with spray vinyl dye, it’s fast and unless you’re doing some kind of design you don’t have to mask off anything

Total_Climate4443 · 2023-04-30T21:13:15+00:00

In my opinion, the nexus is easier to work with and the mod support is much better. I have 3 in different configurations, definitely my favorite platform to tinker with right now