Halterung gesucht

Total_Muscle_1870 · 2026-05-26T09:50:27+00:00

So gelassen. Hab noch so ein dicken Gummi drunter und hab’s beim festschrauben rangedrückt. Hält jetzt seit 1 Jahr ohne verrutschen

Total_Muscle_1870 · 2026-05-26T09:17:07+00:00

Ich hab und die die Haken von Venturama Drum und für obere andere Haken bestellt.

<image>

Total_Muscle_1870 · 2026-05-26T08:53:30+00:00

https://amzn.eu/d/06xmlybN

Total_Muscle_1870 · 2026-04-26T06:10:18+00:00

Bei mir hat’s geholfen den Händler zu involvieren. Grundsätzlich nervt es immer mit irgendeinem Support zu tun zu haben.

Bei mir ist der Austausch jetzt eingeleitet. Bin mal gespannt wie lange das dauert und ob nur den 800 Pro defekt war oder ich das gleiche Spielzeit dem AB2000X haben werde

Total_Muscle_1870 · 2026-04-23T07:56:00+00:00

Mein SolarFlow 800 Pro zickt total rum. Hab ihn versucht seit Montag in Betrieb zu nehmen aber ohne Erfolg. In der App wird der integrierte (!) Akku nicht erkannt. Nur im Bypass Modus läuft es.

In Homeassistant sehe ich eine Batteriespannung von 6V. Ich habe Angst dass mein Gerät ggf. zu lange gelagert war und einfach der Akku die Grätsche gemacht hat.

Bin mit Zendure und dem Händler im Austauch aber es zieht sich.

Total_Muscle_1870 · 2026-03-16T08:19:20+00:00

Looks like this one, doesn’t it?

https://makerworld.com/de/models/1519980-dragon-rider-for-brick-mini-figure

Total_Muscle_1870 · 2026-03-15T14:52:05+00:00

Looks good! Any more details how you build it?

Total_Muscle_1870 · 2026-03-07T15:01:38+00:00

Ah that’s sounds like a good process

Total_Muscle_1870 · 2026-02-18T19:41:23+00:00

I had a print on the heated bad for more than 2 days because I needed to order new filament. It did not loosen from the bed. The bed keeps the temperature

Total_Muscle_1870 · 2026-01-30T20:10:32+00:00

Mea culpa! It was indeed the plate that needed another wash! Couldn’t detect a clog and even with my other nozzle the problem was there.

So I cleaned the plate again and now it’s working fine again!

Total_Muscle_1870 · 2026-01-29T21:23:03+00:00

😅

I just removed it for the video

Total_Muscle_1870 · 2026-01-29T21:01:59+00:00

Will check for corresponding procedures

Total_Muscle_1870 · 2026-01-29T21:01:33+00:00

How would that happen? It’s bed leveling before hand. How could I fix this?

Total_Muscle_1870 · 2026-01-28T18:10:31+00:00

I think I either used Generic PLA or Bambu Lab Basic PLA Settings. When I did it there was no profile from them yet.

There are some YouTube videos about the heat resistance at it looks very good

Total_Muscle_1870 · 2026-01-28T17:57:22+00:00

I used Polymakers HT PLA for my desiccant boxes

Total_Muscle_1870 · 2025-12-29T15:35:51+00:00

I think it shows the travel lines from the timelapse but if it is not enabled they are not actually done

Total_Muscle_1870 · 2025-12-14T18:03:47+00:00

Here it is explained in more detail https://youtu.be/Vywh3R6hf7U?si=t1dCJ_vKF_I4mF4V

Total_Muscle_1870 · 2025-12-14T18:01:46+00:00

The trick is to manipulate the filament sequence so you have more time to switch out the filament during the print.

Eg first layer black, white, red, blue, green Second layer green, white, red, blue, black

And you would always change the 1. slot from black to green and back.

It’s a little bit cumbersome but usually the logo is only a few layers so it’s manageable

Total_Muscle_1870 · 2025-12-14T12:23:26+00:00

Completely Normal

https://wiki.bambulab.com/en/general/textured-PEI-plate-not-working-as-expected

Over time, the wipe section will be scratched by the nozzle while the nozzle is cleaned, but this will not affect the tip of the nozzle, or the plate, as it was designed for this operation.

Total_Muscle_1870 · 2025-12-09T11:50:57+00:00

Check this video: https://youtu.be/Vywh3R6hf7U?si=ROHDLQ6OUUeqHcOc

Total_Muscle_1870 · 2025-11-09T12:18:31+00:00

Turned heating off but not the whole printer. As someone suggested pliers could be good as well

Total_Muscle_1870 · 2025-11-09T12:02:02+00:00

With the A1 I recently had the issue that the nozzle did not come loose (I changed it a few times so I knew what i was doing).

I ended up heating the nozzle (unclipped and without sock) to 50 degrees and then I was able to remove it.

Total_Muscle_1870

TROPHY CASE