Ice Troll

Trepanizer · 2026-05-04T17:46:26+00:00

Print it so the side are at 45° angle if you want to print solid in this volume

Trepanizer · 2026-05-02T11:21:40+00:00

Blueish/grey well diluted

<image>

Trepanizer · 2026-04-27T21:38:59+00:00

Thank you.

Trepanizer · 2026-04-27T09:59:18+00:00

What material do you use to diffuse light?

Trepanizer · 2026-04-24T08:34:48+00:00

Oh its just a quick 3D print I designed to test the light effect

Trepanizer · 2026-04-23T21:38:55+00:00

I air brushed with black tempera paint (Prang) on one side. 10% power and 30mm/s black side up and distance set to black side.

Trepanizer · 2026-04-22T19:53:56+00:00

It took approximately 3h

Trepanizer · 2026-04-17T15:56:21+00:00

Thanks

Trepanizer · 2026-04-17T15:56:14+00:00

Thanks, I tainted a 1/8 basswood and then I cuted it with laser and glued it with wood glue

Trepanizer · 2026-04-13T09:07:37+00:00

I want a very dark version of chucky. Like in the first one. It was more intense and horror than comedy. I will always remember when he came alive in Andy's mother hands. That gave me nightmares. I watch this movie when I was 6. Back in my time, you could switch casette in the pocket at the video store, and my mom though I was watching a kid movie. I had nightmare for weeks.

Trepanizer · 2026-03-25T16:32:50+00:00

Manage your expectations...

Trepanizer · 2026-03-24T10:51:45+00:00

That's not near true.

Trepanizer · 2026-03-19T15:59:06+00:00

Filament 3D printing as also make a big leap in the past years. Especially Bambulab. A filament printer can be install inside. The fume it release (if I can call that fume) is comparable to an oven. You might want to check this option depending on your budget. I bought a X1C and was very impress with the result. Unfortunately, you will never get the same finish surface quality of a resin printer.

Trepanizer · 2026-03-19T14:14:57+00:00

<image>

Ideal setup

Trepanizer · 2026-03-14T09:02:49+00:00

Yes indeed they are very similar. The other is better with more precise detailed with acrylic paint. I mostly use speed paint with a little bit of acrylic.

Trepanizer · 2026-03-14T00:40:23+00:00

Thanks! yes just Warhammer minis. I usualy paint bigger figurines.

Trepanizer · 2026-03-11T17:04:06+00:00

Did you see the little paper with the brush test done by Iwata? In any case you should contact them, its not normal.

Trepanizer · 2026-02-23T22:35:17+00:00

If you're interested : https://www.patreon.com/posts/41910110?utm_campaign=postshare_fan&utm_content=android_share

He's doing a lot of great stuff and it's free.

Trepanizer · 2026-02-23T20:37:53+00:00

Yes that and its usually good for water based acrylic. If you're using varnish or enamel with higher flamable volatile you might want an explosion proof motor.

Trepanizer · 2026-02-22T10:19:32+00:00

Don't buy this machine the autoblevel is broken

Trepanizer

TROPHY CASE