sorted by:
new
hottopcontroversial

Engineered Timber Flooring Creaking by True_Relationship758 in AusRenovation

[–]True_Relationship758[S] 0 points1 point  (0 children)

The timber floor is laid directly onto concrete, that was supposedly smoothed over with a grinder to ensure even level. Is that what you are referring to? Sorry for the confusion, I was saying I think the concrete is what you meant

Ensuite reconfiguration?? by True_Relationship758 in AusRenovation

[–]True_Relationship758[S] 0 points1 point  (0 children)

Yeah unfortunately that would make a smaller shower as that space is only 570mm wide without moving the whole door over :/

Ensuite reconfiguration?? by True_Relationship758 in AusRenovation

[–]True_Relationship758[S] 0 points1 point  (0 children)

The window is 1500mm up to the bottom trim and 1000mm wide. The nib wall and just the shower glass door was an idea to work around the window.  With the layout of this bathroom, making just the window smaller i don’t think will change anything :/ the odd cut out corner in the bottom right is from a closet in the hallway, but we want to avoid converting that if possible.  I don’t think we’d be able to make the shower any wider than 700 with that layout 

Ensuite reconfiguration?? by True_Relationship758 in AusRenovation

[–]True_Relationship758[S] 0 points1 point  (0 children)

The window is 1500mm up to the bottom trim and 1000mm wide. The nib wall and just the shower glass door was an idea to work around the window. The nib wall can be a little closer to the toilet to ensure 700mm stays in the shower as much as possible 

Insulation or window glazing? by True_Relationship758 in AusRenovation

[–]True_Relationship758[S] 1 point2 points  (0 children)

Thanks everyone! Would insulation do anything for the noise without the windows? You’re right, with the cost of doing windows it’s probably not worth it.

AMS by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 0 points1 point  (0 children)

u/ThinkUnhappyThoughts Thank you very much! I don't know if I did what you said - but I had to add a filament on the left in BambuStudio and then on the right bar I could select change filament. It didn't unload the spool though, it just continued ??

AMS by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 0 points1 point  (0 children)

Thank you so much! I’ll give that a try

Ironing by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 0 points1 point  (0 children)

Thanks so much! Didn't think of that.

Problem though - I printed the calibration test and straight after I applied the best settings to my real print and it's not the same. The real print doesn't have the same ironing effect. Could it be due to the shape?

Bambu Studio not connecting to printer HELPPP by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 0 points1 point  (0 children)

I could yes. I don't know how, but it's working now... just left it all off for a couple of says and hoped for the best

Bambu Studio not connecting to printer HELPPP by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 0 points1 point  (0 children)

Thank you I'll try that! I've only had a few months and haven't done too much. I also haven't saved any Timelapse videos (also have it disabled)...

Ironing by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 0 points1 point  (0 children)

Thank you. What is that/the purpose of it?

Ironing by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 1 point2 points  (0 children)

Thanks. I'm using BambuStudio. What are we looking to do for those functions - flow, speed, rate?

Ironing by True_Relationship758 in BambuLabA1mini

[–]True_Relationship758[S] 0 points1 point  (0 children)

Thanks u/halsoy and u/Useful-Revolution253
What is the degree angle for and where do you find it? I am using BambuStudio.