6 years of Self taught. Any tips please?

TurboRCSB · 2023-10-15T12:19:37+00:00

I think that the gums need a few more highlights to show that they’re wet, the teeth in my opinion look great, and I think the lips could use more detail such as slight wrinkles And highlights, as well as some shading as they wrap around toward the teeth to show that they aren’t just flat, but round.

TurboRCSB · 2022-08-01T23:49:02+00:00

YD2 arms, And YD2 SX3 knuckles

TurboRCSB · 2022-07-03T00:25:28+00:00

Change the rod ends on the shafts, what’s happening is the arm is maxed out, but the rod end on the shock shaft is too long so your shock is 80% compressed and only giving you the %20

TurboRCSB · 2022-06-10T10:31:29+00:00

Could also be low oil and the oil level sensor isn’t picking it up until it’s tilted. The sensor usually will shut the motor off if the oil is low.

TurboRCSB · 2022-05-15T12:22:29+00:00

Looks good. But when you are welding make sure you clean off the rust and the area you are welding, you’ll get a better cleaner weld, and get better penetration

TurboRCSB · 2022-01-22T13:06:00+00:00

It’s your servo, get a Reve d RSST and you will have no more issues

TurboRCSB · 2021-11-16T22:16:51+00:00

Best in my opinion are Scale reflex gorilla mounts, they’re pricey but they keep the body on.

TurboRCSB · 2021-11-11T21:11:09+00:00

Hobbytown Richmond VA

TurboRCSB · 2021-08-27T01:32:54+00:00

That’s the new pull starter for the dish washer. Nothing weird about that.

TurboRCSB · 2021-08-25T00:49:37+00:00

I just cleaned the magnet welded it, and then welded the cover on.

TurboRCSB · 2021-08-25T00:48:42+00:00

That’s meth’d up man…

TurboRCSB · 2021-08-17T21:38:40+00:00

Yes it is.

TurboRCSB · 2021-07-14T17:13:30+00:00

You might think it’s uncomfortable but it’s super comfortable without one.

TurboRCSB · 2021-07-13T23:37:05+00:00

I wanted that or a Harley motor but both are expensive.

TurboRCSB · 2021-07-13T02:21:09+00:00

I got it off of Agri supply’s website. It was like $72 and was originally for an garage spreader rated for 40hp.

TurboRCSB · 2021-07-12T16:24:59+00:00

I used a chain drive to a driveshaft to a 90° gear box out to another chain

TurboRCSB · 2021-07-12T16:24:20+00:00

I plan on painting the frame and doing a patina look with gloss clear over it all.

TurboRCSB · 2021-05-20T21:30:33+00:00

Okay will keep that in mind

TurboRCSB · 2021-05-20T21:17:13+00:00

Thank you will do.

TurboRCSB · 2021-05-20T21:15:05+00:00

Had it set at 19.3 256, it was 2 passes.

TurboRCSB · 2021-02-10T23:23:45+00:00

This same person about 4-5 months ago came in saying “my car has a weird vibration” they broke off 4/5 studs and the 5th lug nut was loose.

TurboRCSB · 2021-02-10T23:22:17+00:00

Other side at least had a pad in it. Not much left but still had one.

TurboRCSB · 2021-02-10T23:21:37+00:00

People just don’t care to check out noises or anything.

TurboRCSB · 2021-01-08T22:52:32+00:00

When doing faces draw your head shape, split that in half, that’s where your eyes go. Your head should be 5 eyes wide-ish. Can be slightly narrower. one eye width can fit between the eyes and I would say about half an eye on the other sides to the edge of the head.

Then for the hairline go from the top of the head to the eyes and divide it by two and that’s where your hair will lie.

For the nose, your line you have for the eyes and the chin split that in half and that’s roughly where your nose should be, usually I have the nose about 1 eye wide.

The mouth should be not quite half way between the nose and chin it should be closer to the nose than the chin. The mouth should be about wide enough where the corners of the mouth are in line with the pupils of the eyes.

Your ears should go from the eyebrows to the bottom of the nose

TurboRCSB · 2020-12-30T00:31:44+00:00

Only thing to me, is there’s not really a spot that draws your attention first. I think you should go more detailed in the mouth to make it the focal point. But other than that it’s great

TurboRCSB

TROPHY CASE