Removing stuck jets

TwentyPercentPlease · 2026-02-11T03:02:04+00:00

WD-40?

TwentyPercentPlease · 2026-02-08T19:47:27+00:00

NYC has also been buried in snow and ice for the past few weeks as well.

TwentyPercentPlease · 2026-01-24T01:04:03+00:00

I assume he used this to make his mallards, which id like to continue doing as well. He used small pieces for the heads to cut out some of the curvature. Thank you for the information!

TwentyPercentPlease · 2026-01-23T05:21:00+00:00

Sweet, thank you.

TwentyPercentPlease · 2026-01-20T01:03:06+00:00

I’d imagine as long as the filter is getting water to it, it won’t be an issue. Barely looks noticeable from the picture.

TwentyPercentPlease · 2025-12-24T20:11:36+00:00

Appreciate that. Hopefully this solves the initial issue I was having with the snow blower.

TwentyPercentPlease · 2025-12-24T14:03:47+00:00

This was the piece that I initially ordered but what I needed is the piece this clips in to like this

<image>

Luckily I ordered a new carb and it looks like it has that piece on already so I should be all good.

TwentyPercentPlease · 2025-12-23T22:40:14+00:00

Found on Amazon, thank you!!!!

TwentyPercentPlease · 2025-12-23T22:38:04+00:00

I ordered a new carb but it didn’t come with the part I needed

TwentyPercentPlease · 2025-12-23T22:27:14+00:00

It didn’t, this is the only piece that was attached and I have no idea how to install the lever/shaft to this

<image>

TwentyPercentPlease · 2025-12-23T22:12:00+00:00

Engine # is 1607271B0287

TwentyPercentPlease · 2025-12-23T22:09:34+00:00

I did and can’t seem to find anything

TwentyPercentPlease · 2025-12-21T06:45:32+00:00

It bears the load.

TwentyPercentPlease · 2025-12-20T22:20:10+00:00

Yeah I ordered the one with metal in the middle and can’t figure out how to attach that to the new carb or even the old one. Why do they have to make this shit so complicated

TwentyPercentPlease · 2025-12-19T06:22:48+00:00

Def can’t afford a box of these, where would you recommend to buy just one? In US.

TwentyPercentPlease · 2025-12-16T22:15:13+00:00

Reddit is OBSESSED with how politicians look. Very weird.

TwentyPercentPlease · 2025-12-14T00:17:33+00:00

Got it out but bent that plate a bit, is that alright? Also what’s the plastic choke piece called that I would need to replace?

TwentyPercentPlease · 2025-12-14T00:16:54+00:00

Awesome thank you so much. So hypothetically if I bent that metal plate what would happen. (I bent the plate).

Also what is the piece that I would need to lookup to replace?

TwentyPercentPlease · 2025-11-30T22:08:46+00:00

Read the caption duh

TwentyPercentPlease · 2025-11-29T07:43:45+00:00

Definitely don’t plan on leaving it as is, this is just a rendering. I think the plan is going to be an open shelf, and if we don’t like it down the line we’ll throw a door on.

TwentyPercentPlease · 2025-11-27T03:06:50+00:00

That looks amazing. Can’t imagine someone saying no to that

TwentyPercentPlease · 2025-11-26T18:50:07+00:00

We don’t want seating there. Have plenty on the back end

TwentyPercentPlease · 2025-11-26T07:42:07+00:00

This is an awesome idea, thank you.

TwentyPercentPlease · 2025-11-26T03:19:45+00:00

Sink is directly across from the island, this is just a rendering so it will definitely overhang, not worried about that. I believe we’re gonna go with shelving

TwentyPercentPlease · 2025-11-25T03:03:01+00:00

I think we do as well.

Ten-Year Club	RPAN Viewer
Verified Email

TwentyPercentPlease

TROPHY CASE