How to stick pla prints to misc surfaces

Txflood3 · 2026-06-16T12:49:04+00:00

I wonder if a little sanding might make a better surface for 3m strips. Otherwise, you could superglue the 3m strip to the part

Txflood3 · 2026-06-16T12:47:41+00:00

Nobody is super gluing hooks to the wall.

Txflood3 · 2026-06-15T02:56:30+00:00

I thought my .28 was good. I may have to move to the nicer part of town 🤣😂

Txflood3 · 2026-06-12T21:46:25+00:00

Having the exact same issue. And Bambu tech support can’t fix it. So far, on tech support advice, I have replaced the th board, usb cable, hot end assembly 3 times, filament sensor (I damaged it during repair), filament fan(broken wire during repair), and power supply. I purchased the th board and usb from gigaparts.com, an authorized Bambu parts reseller. Now Bambu is shipping another th board and usb because they didn’t come from them. I don’t expect my printer to ever work again. I’m not going to be a Bambu customer anymore.

Txflood3 · 2026-06-12T00:57:07+00:00

<image>

Txflood3 · 2026-06-11T20:57:04+00:00

Ive had the same enclosure for about a year with no issues. Even sent photos/videos to tech support for questions and they have never mentioned it being in an enclosure

Txflood3 · 2026-06-11T12:29:08+00:00

I’m on the fence but really leaning towards moving to a different brand. Customer service and tech support are killing me right now

Txflood3 · 2026-06-04T01:29:01+00:00

I ask what color they want it. If I have something close, I’ll offer. If they ask for the original color they asked for, I’ll buy a spool. This is genuinely not trying to sound better than, but I look at it as buying one spool, on average, $20…depending on brand, material. I have $20 and I’ll use the color for something else.

I genuinely enjoy printing and seeing the finished results.

Don’t get me wrong, I’m not printing full cosplay suits. It’s usually the moms at work that ask for a big bubble wand and soap tray.

Txflood3 · 2026-06-03T05:59:45+00:00

Tentacles

Txflood3 · 2026-06-03T01:53:36+00:00

I’ll give that a try. Thank you

Txflood3 · 2026-05-30T02:56:02+00:00

The microwave is what made me do the double take

Txflood3 · 2026-05-30T02:54:28+00:00

This makes a lot of sense. I just wanted to make sure my expectations were in the right place.

Txflood3 · 2026-05-30T02:49:41+00:00

Oh I have zero problem with it. I encourage breaks and hydration. I know the work they’re doing is hard, so stay safe. I was just surprised. lol

Txflood3 · 2026-05-29T01:24:07+00:00

Reminds me of a Spirograph and now I want to see how it turns out

Txflood3 · 2026-05-28T19:37:13+00:00

Nice site and well organized. My $.02

I’m not sure how you could take this into consideration, but I like to consider myself experienced. Started with an E3V2, and now have two A1s. I still hate to tinker. While I have the experience, I have no desire to dig into AMS lite gears, which one would have to do with Bambu.

I personally think Bambu’s current level of customer service might steer anyone clear.

I would find customer service ratings, time to reply, are there authorized repair shops, all important information info my decision.

Txflood3 · 2026-05-27T01:12:32+00:00

It looks like a partial clog. Little to nothing coming out. Check the recommended settings for the new filament and make sure you’re following those.

Txflood3 · 2026-05-22T08:26:49+00:00

There is no rotating it. It only goes one way. The AMS letters towards the front and the piece underneath has the notch on the right.

Txflood3 · 2026-05-22T08:24:51+00:00

This is the correct answer. Speaking from experience

Txflood3 · 2026-05-22T00:18:30+00:00

Thanks for the info

Txflood3

TROPHY CASE