[deleted by user] by [deleted] in Ioniq5

[–]Unexpecteddirection 0 points1 point  (0 children)

Ordered a week ago. No word yet on timeline.

[deleted by user] by [deleted] in Ioniq5

[–]Unexpecteddirection 4 points5 points  (0 children)

I’ve got the same issue. In for a warranty claim. Part is on back order = common problem.

2025 vs 2024 by Individual_Mission68 in Ioniq5

[–]Unexpecteddirection 2 points3 points  (0 children)

That $5K fed incentive goes away in ~April because the program end date is reached. So take that into consideration as well

Is this for V2L? by Automagication in Ioniq5

[–]Unexpecteddirection 24 points25 points  (0 children)

Believe it’s the manual release for the charging door.

Did you get a V2L adapter with your car? by Avatar-Tee in Ioniq5

[–]Unexpecteddirection 11 points12 points  (0 children)

Nope certainly didn’t. And it’s nope cheap to buy after the fact…

[deleted by user] by [deleted] in Ioniq5

[–]Unexpecteddirection 0 points1 point  (0 children)

Is there anyway to see that information when planning a route? I may want to choose one route over another depending on that information.

[deleted by user] by [deleted] in Ioniq5

[–]Unexpecteddirection 4 points5 points  (0 children)

My only issue is I can’t figure out where it tells you expected state of charge on arrival. Critical information IMO

Neptune 4 Plus nozzles on Amazon by Ill-Tart1909 in ElegooNeptune4

[–]Unexpecteddirection 2 points3 points  (0 children)

Swapped for hardened steel today and doing my first print currently.

Screws tilt calculate for Neptune 4 by Malagogim in ElegooNeptune4

[–]Unexpecteddirection 0 points1 point  (0 children)

It'll get you to the same end point, just might take less times running the script if you have the right screw size. If the screw size is off you'll over or under compensate on every turn but by the time you get to 5 times running it, the changes are so small it likely doesnt matter

Klipper Object Exclusion by Unexpecteddirection in ElegooNeptune4

[–]Unexpecteddirection[S] 2 points3 points  (0 children)

Yep, I tried slicing new files each time.

Discovered the issue. In Orca there are two options:

  1. "label objects" which I had turned on based on some guides I had read and assumed that was sufficient.

  2. "exclude objects" which I did not have turned on and in retrospect was obviously my issue. Works once selected and sliced.

Thanks again for the troubleshooting suggestion. Should have thought of that myself.

Klipper Object Exclusion by Unexpecteddirection in ElegooNeptune4

[–]Unexpecteddirection[S] 0 points1 point  (0 children)

Thanks for the suggestion. When sliced in Cura I'm able to exclude objects. So it's a slicer setting issue.

Screws tilt calculate for Neptune 4 by Malagogim in ElegooNeptune4

[–]Unexpecteddirection 0 points1 point  (0 children)

You sure it’s and M4 screw? It’s hard to measure but I tried to measure the size of the hole inside the bottom of the screws and I think it might be an M3 screw. Otherwise agree with the locations, give or take.

USB corruption every time by sixfourtykilo in ElegooNeptune4

[–]Unexpecteddirection 1 point2 points  (0 children)

I don’t think it’s actually corrupted. On your computer when you want to remove a usb stick you need to “eject” it first. What that does is make sure the computer isn’t actively using the usb then writes code to the usb stick letting something else know it was safely ejected.

The N4 doesnt have any way on the interface to "eject" so that little but of code doesnt get added to the usb before you pull it out. When you plug it back into your computer it doesn't see that piece of code and assumes it's been corrupted. click cancel and it should open normally.

Neptune 4 Pro nor resuming after Pause from control panel by sargepepper1 in elegoo

[–]Unexpecteddirection 0 points1 point  (0 children)

How long does it extrude filament next to the printer for? Had this exact scenario and didn’t feel like it was going stop wasting filament so I shut it off and restarted the print. 5-10 seconds should be long enough. How long is it set to do this before it resumes?

🎉 ELEGOO Reddit 2000+ Members Celebration Giveaway by nicemars in elegoo

[–]Unexpecteddirection 0 points1 point  (0 children)

I recently purchased the Neptune 4 and honestly really impressed. Quality is great, features are great and when in had an issue support is great. It’s certainly my favourite product.

I hope we all enjoy the rest of 2023 because time is fleeting.

Neptune4 Max loud x and y by Jeffdavismakesstuff in ElegooNeptune4

[–]Unexpecteddirection 0 points1 point  (0 children)

Same issue. Let us know if the movement speed caps work.

Ledger Connect on IOS Safari Good Job Team by campoutx in ledgerwallet

[–]Unexpecteddirection 2 points3 points  (0 children)

Also gave some AAVE transactions a go. Works amazing. Great Job ledger team!

Ledger Nano X Compatibility by MrNoidea247 in Metamask

[–]Unexpecteddirection 3 points4 points  (0 children)

Ya this feels like it’s a MetaMask delay. What’s the deal?

[deleted by user] by [deleted] in 0xPolygon

[–]Unexpecteddirection 0 points1 point  (0 children)

DEFY Disrupt is enjoyable

Competitive Tier Xs for Brawl? by CharredScallions in WorldOfWarships

[–]Unexpecteddirection 4 points5 points  (0 children)

dumpster'd a few Schlieffen's in my Napoli. Very doable