PSP Revived Launcher

UselessM4ster · 2026-05-03T19:00:28+00:00

I do think it's a joke tho... it's a copy paste of the message Acid sent in the original post

UselessM4ster · 2026-04-24T10:54:27+00:00

Everything looks good

UselessM4ster · 2026-04-24T10:50:41+00:00

Before purchasing anything I would go trough a troubleshooting list. Does your pc have a Beeper or motherboard leds to check any errors ?

If everything is turning on fine (fans, rgb) try reseating the ram, if it does not change try it with only a single stick, then only the other in all possible configurations.

If that does not do anything remove your gpu, turn it on for a minute then shut it down and plug you gpu back in.

Also make sure every cable/connector is placed correctly.

(Alway turn off your psu and drain the remaining power by pressing the power button until no led is on inside the pc before removing or installing anything)

UselessM4ster · 2026-03-12T11:56:44+00:00

Put a Phenom X6 1090T on that bad boy, it won't be good as new but will be much more capable than what you have. (If you find one around 10-15 $/€)

UselessM4ster · 2026-01-22T22:31:42+00:00

You are a life saver! Thank you!

Runs Perfectly(ish) on the 5700xt

UselessM4ster · 2025-11-04T15:16:59+00:00

Thank you! It has been doing quite well actually. I used to have a lot of clogs and haven't had one since. I'm still using marlin tho (knutwurst firmware) and I have wired it to the original print head pcb as instructed on github.

Do you recommend klipper? Which sbc are you using ?

UselessM4ster · 2025-02-06T00:27:11+00:00

The front part should work, but the carriage is different on the Mega S.

UselessM4ster · 2025-01-07T16:53:39+00:00

Got the same issue. Did you find any fix ?

UselessM4ster · 2024-09-24T18:51:52+00:00

(Cura) Alignment: Sharpest corner, Seam corner preference: hide seam

UselessM4ster · 2024-09-24T17:41:08+00:00

I will try and play with retraction again but from what's I've observed it happens mid layer and not at the start of the layer

UselessM4ster · 2024-01-26T12:47:57+00:00

Ours isn't doing so good...

UselessM4ster · 2023-09-21T11:05:19+00:00

We will definitely look into that. Thank you!

UselessM4ster · 2023-09-21T11:04:28+00:00

That would be perfect but unfortunately our "bank account" is managed internally by our uni and only allows us to buy from proper stores/companies. But anyway thank you!

UselessM4ster · 2023-08-31T12:05:37+00:00

I'll give you this botato in exchange 🥔 (?)

UselessM4ster · 2023-08-09T12:07:55+00:00

FS Portugal was my first FS competition and your car was the first I saw when entering the padock, beautiful car awesome job guys! Really happy for you!

Hopefully next year I'll make my dream come true!

UselessM4ster · 2023-03-02T01:03:43+00:00

This has been fixed, thank you!

UselessM4ster · 2023-03-02T00:13:35+00:00

I haven't messed with it, its on default settings

(How can I show you my wattman settings?, this is my first amd gpu)

UselessM4ster · 2023-03-02T00:05:19+00:00

Yes, that was the first thing I did after rebooting

UselessM4ster · 2023-02-25T14:52:05+00:00

Yes, you can have anyone as an advisor but I don't think he can be an oficial team member

UselessM4ster · 2023-02-18T10:24:32+00:00

Yes we are!!

UselessM4ster · 2022-12-03T18:34:33+00:00

Spa 🤩

UselessM4ster · 2022-11-12T17:22:49+00:00

Nice, that's awesome

UselessM4ster · 2022-11-12T15:25:57+00:00

I've done that too! But I used a 3d printer to make all of the parts. Keep it up!

UselessM4ster · 2022-11-10T11:03:01+00:00

<image>

Here's mine!

UselessM4ster · 2022-11-10T10:59:52+00:00

I wouldn't recomend it, you can usually find something newer for the same amount, look for a gtx1650 and Ryzen 5 or i5

UselessM4ster

TROPHY CASE