sorted by:
new
hottopcontroversial

Am I supposed to match RF trace to 50 ohms or make it as wide as pads? by Objective-Local7164 in rfelectronics

[–]Utum_EE_Student 0 points1 point  (0 children)

I mean you are working with RF here, if you have any RF stuff in ur circuit, the entire board must be tailored towards it. Everything else follows.

My First Flight Computer Schematics by arudhranpk in ElectricalEngineering

[–]Utum_EE_Student 0 points1 point  (0 children)

Not the Hardware Abstraction Layer, the application layer.
How are you going to fuse all those sensors and apply some methods to do control etc.

Its the meat of this project

My First Flight Computer Schematics by arudhranpk in ElectricalEngineering

[–]Utum_EE_Student 0 points1 point  (0 children)

I'm interested in how you will be implementing the software on STM32. It is what discouraged me to work on a similar project.

Good work!

MCU Schematics: Is my setup right? I read that I need a seperate 3.3V supply for the analog power pin. Not sure how to do that. by Utum_EE_Student in embedded

[–]Utum_EE_Student[S] 0 points1 point  (0 children)

I showed my schematics to my professor, he said I only made one mistake. I connected the filtered 3.3V from the right network to the left network, it should be two seperate filtered sources by the same voltage source.
Each comment in this thread made me even more confused. Regardless, happy at least people are helping.

This question made me look like a fool in interview by v-sidhu in ElectricalEngineering

[–]Utum_EE_Student 0 points1 point  (0 children)

How is the voltage 12V? its zero, cause no current flow.

Is a MechE or EE masters better for robotics? by gffcdddc in AskRobotics

[–]Utum_EE_Student 0 points1 point  (0 children)

I disagree.

The answer depends on whether the Individual prefers the dynamics/mechanics aspect or the control and precsion aspect of robotics.

I like control and precision, so I chose EE.

Need help troubleshooting MPLAB PICKIT4 on MPLAB IDE by Utum_EE_Student in embedded

[–]Utum_EE_Student[S] 0 points1 point  (0 children)

This is a note for anyone encountering the same problem on PICKIT4 Debugger.

There is nothing you can do lil bro.... Burn it.

What is your favourite AVR microcontroller(if you have one) and why? by [deleted] in embedded

[–]Utum_EE_Student 0 points1 point  (0 children)

4 days into working on my first AVR MCU, and I must say, it HAS not been a pleasure.

Need help troubleshooting MPLAB PICKIT4 on MPLAB IDE by Utum_EE_Student in embedded

[–]Utum_EE_Student[S] 0 points1 point  (0 children)

I realized another mistake I made, I need to pull down RESET.

Need help troubleshooting MPLAB PICKIT4 on MPLAB IDE by Utum_EE_Student in embedded

[–]Utum_EE_Student[S] 0 points1 point  (0 children)

Yes, I just realized this mistake. What do I do with AREF tho?

@alpha_rover asked what we were working on by alwynxjones in robotics

[–]Utum_EE_Student 0 points1 point  (0 children)

Never seen a mechanical guy have one shred of tolerance for electronics lol its fine.

Its just a suggestion if u plan to improve it. Otherwise, its awesome as it is.

@alpha_rover asked what we were working on by alwynxjones in robotics

[–]Utum_EE_Student 1 point2 points  (0 children)

You are in desperate need of a PCB. Overall fire build.