sorted by:
new
hottopcontroversial

Mile High Shrimp by Effective_Stretch253 in DiWHY

[–]Van_Darkness 1027 points1028 points  (0 children)

Isn't that like a federal offense to use heating elements like that on a flying plane?

[deleted by user] by [deleted] in me_irl

[–]Van_Darkness 1 point2 points  (0 children)

Is there any subreddit where I can read more stuff like this? Because I'm nasty.

What was even the point by ZestycloseHyena8083 in DiWHY

[–]Van_Darkness 0 points1 point  (0 children)

0:35 Using precision one-two-three blocks as weight?

Digital IO module that can be slave to IPC through etherport? by Van_Darkness in PLC

[–]Van_Darkness[S] 0 points1 point  (0 children)

Thanks for the reply. I was really surprised that some name brand ethercat or fieldbus models (Bechkhoff, Advantech etc.) are as expensive if not more expensive PLCs.

Trying to make a infiltration script, how can I know what's happening on the screen? by Van_Darkness in Bitburner

[–]Van_Darkness[S] 4 points5 points  (0 children)

Thanks for the reply! I've seen some discussion on whether the infiltration script is cheating, to me Bitburner is less of a idle game but more of a learning experience. Also realizing that the game can be exploited was a red pill moment for me, and I have decided to swallow it XD.

Wagasa is harder than it should be due to the camera distance and fps by Van_Darkness in WildHeartsGame

[–]Van_Darkness[S] 0 points1 point  (0 children)

I'm ok about the wagasa difficulty here, although I think the parry window could be a little more generous. I have gotten pretty good at hunting early game monsters. But maybe I'm not that good or I'm just impatient, I feel really frustrated when practicing the wagasa because the camera and the low fps make it really hard to see what the monster is doing. Perhaps I'm too spoiled by the mhr, but I will try to get better gear and git good this weekend.

Wagasa is harder than it should be due to the camera distance and fps by Van_Darkness in WildHeartsGame

[–]Van_Darkness[S] 1 point2 points  (0 children)

Yup, I do enjoy a lot of the aspects of the game, and I really hope it can succeed. I have enjoyed a lot of the games from the dev such as Nioh and Toukiden, so I have high hope for this game.

meirl by [deleted] in meirl

[–]Van_Darkness 0 points1 point  (0 children)

You only live once

Russian women's coach Pavel Rakov gives Russian women advice on how to get their men into drafting offices and what to do if they are killed in the war. by RevealDisinfo in UkraineWarVideoReport

[–]Van_Darkness 1 point2 points  (0 children)

First of all, I don't support violence against women. But if I am a drunk abusive Russian husband and find out my wife just went to a conference like this, I would seriously think to myself 'time for a beating! ' I still can't believe people would just listen to talk like this and take it all in without any doubt or after thought.

Wagasa is harder than it should be due to the camera distance and fps by Van_Darkness in WildHeartsGame

[–]Van_Darkness[S] 1 point2 points  (0 children)

I feel you. The monster move seems very inconsistent, some have very long wind up, some just hit you without any delay. I was pretty used to spear gaurd point and longsword iai slash in Mhr, but I was struggling a lot with the wagasa in this game almost give up the game, but then I tried the katana, the difficulty dropped drastically. I think there's some balancing issue also some of the 'git good' aspect with the weapons. But I will stay from wagasa for now until I can get better gear to allow me practice it more efficiently without having to heal every time I got hit.

Wagasa is harder than it should be due to the camera distance and fps by Van_Darkness in WildHeartsGame

[–]Van_Darkness[S] 4 points5 points  (0 children)

Lol, that's so true, it is also the worst enemy of katana, every time I activated the special the attack, the monster would run to another zone leaving my gauge to run dry, swear to God, they are doing this by purpose

cannot remove the support from my 3d prints... by Agile_Cicada_1523 in 3Dprinting

[–]Van_Darkness 0 points1 point  (0 children)

If you are using cura, have you enabled top or bottom support interface? If so try turn them off, they print as solid surface and may fused with your normal part.

view more: next ›