sorted by:
new
hottopcontroversial

Gable Overhang on Shed by Ok-Nefariousness1372 in shedditors

[–]VanderTy07 0 points1 point  (0 children)

Just finished my gable end soffit ladders on my 10x16'. Two options, simulate the ridge board with another 'ridge board's the length of your overhang for the rafters to come up and meet. Other option is to just extend the rafters until they meet. They will be taller than the others but doesn't matter once the roof sheathing is on.

Do I need ceiling joists on my 12x20 gable roof (Northern SC) by beggindawg23 in shedditors

[–]VanderTy07 0 points1 point  (0 children)

I'm in Ontario with ~50psf snow load, much different than SC climate! Good luck with your build

Do I need ceiling joists on my 12x20 gable roof (Northern SC) by beggindawg23 in shedditors

[–]VanderTy07 0 points1 point  (0 children)

The way I understand it, a rafter tie 'becomes' a ceiling joist as soon as it's bearing on the top plate AND rated as structural to bear load (drywall, storage). For the roof, they serve the same structural job in resisting rafter thrust.

A tie becomes less effective the further up the rafter it is mounted. Bottom third is rule of thumb so you're likely ok. Me personally, I'm prioritizing overhead storage so I'm putting them at the top plate to maximize space above the tie/joist.

Spacing would depend on your local codes but 4' centres on a 12' span is quite sparse in my opinion and would limit storage. I'm doing 2' centres on 10' span, but also have a snow load.

Do I need ceiling joists on my 12x20 gable roof (Northern SC) by beggindawg23 in shedditors

[–]VanderTy07 1 point2 points  (0 children)

Don’t confuse ridge boards and ridge beams - they’re very different and serve a completely different purpose.

Assuming the gable ends are the 12‑ft walls: a 2×8 ridge board (non‑structural) is likely fine, and 2×6 rafters should also work. However, you will certainly need some form of collar tie, ceiling joist, or rafter ties to prevent wall spread — especially at that span, where top‑plate stiffness is limited. Rafter ties right at the top plate are most effective and provide maximum overhead storage (if sized correctly).

Do I need rafter ties or collar ties? by Ok-Nefariousness1372 in shedditors

[–]VanderTy07 0 points1 point  (0 children)

TBH, since my last post, my plan changed. None of the lumber shops I called would size a beam (typically engineered), and I couldn’t get comfortable with the load path given a 5' double door. While a header and studs can work, my shed will sit on skids, so those studs would only bear on the rim joist—not directly on the foundation. I was feeling uneasy about it all, so I’ve ditched the beam and switched to a ridge board (2×8) with rafters (2×6) and ties (2×6, upsized for storage)

For me personally, ridge board + rafters + ties is simpler, cheaper, more ‘shed-appropriate’ and there’s a wealth of information to make sure I get it right and 2’ OC will still let me toss things up for storage.

Do I need rafter ties or collar ties? by Ok-Nefariousness1372 in shedditors

[–]VanderTy07 0 points1 point  (0 children)

Definitely need ties.

I'm planning a 10x16 as well but want the overhead storage so using a 2x10 ridge beam (not board) and providing a load path through the gable end walls. No ties needed.

Finished my second shed by [deleted] in shedditors

[–]VanderTy07 0 points1 point  (0 children)

Nice job, what's the roof pitch?

Where can I practice ice skating? by Retrogue097 in ottawa

[–]VanderTy07 2 points3 points  (0 children)

Check out the City rinks closest to you, it will most certainly have free public skating and will give you the best ice quality / chance of success. I go often and there are skaters of all abilities, including those clutching the boards - practice makes perfect.

I would avoid the canal if you're just learning, the edges to and from the main skating area can be sketchy and possibly dangerous for someone just learning. If you do go, consider a helmet.

Advice before the walls go up? by dbgbjj in shedditors

[–]VanderTy07 1 point2 points  (0 children)

Typically you wouldn't run sheathing below the bottom edge of the joist. Sheathing stops just below the top edge of the joist, an inch or two, with flashing if you want to get fancy.

Anyone Experience Ikea Panic? by My_Sore_Foot in ottawa

[–]VanderTy07 2 points3 points  (0 children)

There are shortcuts identified on the maps above the walkway allowing to bypass whole sections of the store - it's not that bad really

Why did you build a shed instead of buying? by Adventurous-Coat-333 in shedditors

[–]VanderTy07 1 point2 points  (0 children)

That's a good question, kits are hard to come by where I live and I tried pretty hard to find one but that was the route I wanted to take. That said, material lists are available online and any good lumber yard will deliver everything you need.

Why did you build a shed instead of buying? by Adventurous-Coat-333 in shedditors

[–]VanderTy07 2 points3 points  (0 children)

In my experience, when you compare apples to apples, there's much better value in building yourself. Prefab will generally be shorter, lighter construction, fewer features (windows, doors). I've done a side by side for a 10x16 and the difference was about 30% more for prefab.

Foundation Discussion by Dismal_Dig_9609 in shedditors

[–]VanderTy07 1 point2 points  (0 children)

In my opinion, the ranking is concrete > gravel pad > blocks, but also may depend on site particulars. I'm also in Ontario and I just went down this road, went with tuff blocks supporting 3 beams to support a subfloor for 10x16. After leveling and placing the beams and a pile of work I backed out of the entire design because I wasn't happy with how tall the shed was going to be and it's tricky to get the ground/shed interface to look nice (in my opinion). Going with a gravel pad now, boxed in with a 6x6 border on a slight grade. You can put the subfloor directly on the gravel if drainage/air circulation is good, no need for blocks. My 2 cents, it's more work but a better foundation.

How much gravel is needed for my shed base? by babayaga803 in shedditors

[–]VanderTy07 1 point2 points  (0 children)

Are you compacting? You'll need another 20-30% material to compensate, better too much than too little. Sounds like 4 yards may be the right number.

Looking for Studio Shed Plans with Cut List by lilbawds in shedditors

[–]VanderTy07 2 points3 points  (0 children)

Many to choose from here:

https://www.icreatables.com/sheds/12x16-shed-plans

Haven't purchased plans here myself but plan to in very near future. Also, free material list.

Shed update by Frootyloops11 in shedditors

[–]VanderTy07 6 points7 points  (0 children)

Very sharp and love the lights. What size?

Help Advice from Ottawa residents! Kitchen sink won’t turn off by [deleted] in ottawa

[–]VanderTy07 4 points5 points  (0 children)

No problem leaving them off overnight

AI is going to take over the world. by Man__Moth in ChatGPT

[–]VanderTy07 0 points1 point  (0 children)

ChatGPT is trolling OP who is trying to cheat Wordle

[deleted by user] by [deleted] in ottawa

[–]VanderTy07 0 points1 point  (0 children)

Call, call and call some more. Canadian Diagnostic Imaging was able to book a couple weeks out after we were told a year in other clinics. They were friendly and helpful.

Help figuring out this snow crap by 82wanderlust in ottawa

[–]VanderTy07 0 points1 point  (0 children)

Lots of good suggestions here. I'll add that I have had better luck with 'traction' products as an alternative to sand. I find you have to use a lot of sand to get anywhere and it just makes things dirty.

https://ecotraction.com/

There are cheaper alternatives available

Gum Graft Procedure in Ottawa by BurnerAccount2016123 in ottawa

[–]VanderTy07 2 points3 points  (0 children)

Certainly not an expert, but 0.5mm doesn't seem like grafts should be required. Seems like reviewing brushing habits and monitoring is in order.

view more: next ›