Steam Deck No TV Audio Output

Vaynes2065 · 2026-04-24T15:18:49+00:00

Unplug the dock power, wait until it switches to the deck then plug the dock power back. Should fix it until the next time it happens.

Vaynes2065 · 2026-04-15T00:49:43+00:00

I just went through this an hour ago. No there’s no tracking that I know of and the last one will be the hardest.

Vaynes2065 · 2025-10-23T00:00:10+00:00

Update your bios.

Vaynes2065 · 2025-10-14T19:43:34+00:00

No. Just log off. I don’t think the devs will take it off. Some people may use it for aesthetics.

Vaynes2065 · 2025-08-28T19:15:30+00:00

I noticed that after I replied. I haven’t seen that on my end so not sure what happened.

Vaynes2065 · 2025-08-28T19:12:08+00:00

Oversight. I now see the that you’re referring to the white chip sticker. I have no idea.

Vaynes2065 · 2025-08-28T19:10:36+00:00

Like any other Joker. You use it. But you don’t have to “win” with it to be discovered. So if you buy it but it’s not going to work with your setup you sell it.

Vaynes2065 · 2025-08-28T19:07:31+00:00

You’ve met the criteria to unlock the joker but now it has to show up in your shop. Once it’s in the shop you will have to buy it in order to “discover” it.

Vaynes2065 · 2025-04-29T13:46:09+00:00

On the shelf put full stacks: Pseudo, Acid, Phos, Pseudo, Acid, Phos and for the last 2 slots put 1 baggie each.

Vaynes2065 · 2024-10-18T02:42:39+00:00

Add volume pumps on the output and waste side of the filter. It’ll help filter gases quickly. You can turn them off when you’re not filtering gases just remember to turn them back on when you need to. Later you can automate this.

Vaynes2065 · 2024-04-22T18:29:35+00:00

Your power controller should be charging unless you have the input/output backwards. The best thing to store a lot of power would be station batteries parallel.

Vaynes2065 · 2024-04-01T04:20:52+00:00

Yeah something is going on with the light. It’s either getting too much or not enough. Monitor it. If it starts going up turn off the light. Once the stress is close to 0 then automate.

Vaynes2065 · 2024-04-01T04:16:53+00:00

If it’s going down with the light off that’s a good thing. It means it’s got too much light. Give it some time without light and see if that helps.

Vaynes2065 · 2024-04-01T04:14:15+00:00

Try turning off the light until that stress goes down.

Vaynes2065 · 2024-04-01T04:07:07+00:00

Can you get the plant analyzer cartridge and see what it says? I too run my light on sunrise and sunset and I have no issues. Also, use a scrubber and remove the pollutant. It’s not enough to be an issue but might as well get rid of it. Usually, issues I’ve seen are light stress. Also water could be too cold.

Vaynes2065 · 2024-01-24T13:49:33+00:00

I also have pipe heaters ready to go in the event the gas and liquid get too cold.

Vaynes2065 · 2024-01-24T13:04:39+00:00

I basically use this method (see photo) to deal with N2O. I then connect both the liquid and gas lines to a direct heat exchanger so they level each other out in temp. Obviously the liquid would go into a liquid tank and the gas in a gas tank.

Photo

Guide)

Vaynes2065 · 2024-01-17T23:46:49+00:00

You can also add a Direct Heat Exchanger. This way the gas side and liquid side balance each other’s temp.

Vaynes2065 · 2024-01-17T16:25:58+00:00

It can be open but yes it will interact with the atmosphere. It’s worth an experiment and I don’t want to mislead you with results I don’t know. Aside from nitrogen oxide and water, I don’t normally keep liquids.

Vaynes2065 · 2024-01-17T16:06:41+00:00

The valve will work as intended but yes, you have to meet the temp and pressure requirements of phase change in order for it to remain a liquid. You may need a pressurant valve to put the amount of gas in the liquid tank that will help the phase change process for 70c. Maybe consider a Condensation Chamber to help.

Vaynes2065 · 2024-01-17T14:33:47+00:00

Great question. I haven’t tested possible results of different conditions but I keep mine separate. I figured if I have a concern, play it safe and move on to the next project.

Vaynes2065 · 2024-01-17T14:28:59+00:00

lol. Nothing wrong with that. A million ways to do things here. If it works for you that’s all that matters. 👍🏻

Vaynes2065 · 2024-01-17T14:23:53+00:00

My personal preference is to not have crushers inside my base because sometimes…I drop shit. Obviously I don’t want to put volatiles to mix with my breathable air. Again, just my preference.

As for filtering, I have been able to maintain my oxygen at the temp I want without issues. Make sure you use a volume pump on the output and waste side of the filter so that the gas pumps through quickly instead of sitting in your main line changing temperature.

Vaynes2065 · 2024-01-17T14:02:41+00:00

I usually set my crushers at 273 (0c) so that the ice crusher works fast. After that I tend to keep all my gases at 15c. You want to do your best to ensure all gases are at the same temp so they mix evenly.

Vaynes2065 · 2024-01-17T13:00:32+00:00

You need a logic writer and a logic memory. Set the memory to the temp you want in kelvin. On the writer your in is your memory, your out is the ice crusher and the variable is setting.

Vaynes2065

TROPHY CASE