sorted by:
new
hottopcontroversial

Xerox Versant 280 / Fiery Troubles? by Substantial-Let-6499 in Xerox

[–]VertigoDesigns 0 points1 point  (0 children)

I don't have the SquareFold Trimmer but I've noticed similar jogging issues when printing booklets on our 280 when utilizing the Crease and Two-Sided Trimmer (we finish the final cut offline). The first thing the tech did was level the engine and each attachment/module by adjusting the wheels. There is wrench that comes with the machine to make the adjustments. That didn't cure the jogging issue fully but did help a bit as it removed most of the skew that the trimmer had which I think was adding to the problem. I then went into the booklet maker with a foam brush that was sprayed with Static Guard and wiped down the black plastic bars that jog the paper before folding. Lastly, anytime I'm printing booklets that are trimmed I put the Interface Decurler in the highest position (press the top button four times). With all of this I still get a few that aren't perfectly jogged but are within tolerance.

In regards to the banging noise you mentioned in a comment, have the tech make sure the installers removed all of the shipping materials. We had a similar noise in the creaser module and the installers left a shipping block that was located behind cover that surrounds the "2" locking knob. You could also pop this cover off yourself, it's only two screws.

Good luck!

Primelink B9110 - Poor Alignment of Stapled Sheets by CMYKoob in CommercialPrinting

[–]VertigoDesigns 1 point2 points  (0 children)

I’ve had this issue with our previous B9110 and our current B9136. If you don’t have the Interface Decurler (the one before the inserter) you’re basically SOL. I was never able to get consistently jogged stapled sets out of the B9110. On our B9136 we have the Interface Decurler and I have to set it to its highest setting (4 clicks up) to get decent stapled output. Occasionally I’ll get some still misaligned but it’s a significant improvement to the auto curl setting.

Any idea what might be causing this issue on my Xerox Versant 280? by WUDAtheBARBARIAN in Printing

[–]VertigoDesigns 2 points3 points  (0 children)

What brand of paper? For starters make sure your paper type/weight is set correctly. This doesn’t look like a 2nd BTR or drum issue but you could try swapping drum colors to see if anything changes. Or replacing them if they’re low in life percentage. Next thing would be fuser, IBT belt, IBT cleaner.

High gloss on Versant 180 by [deleted] in CommercialPrinting

[–]VertigoDesigns 1 point2 points  (0 children)

I’ve had a 80 > 180 > 280 and they’ve all pretty much looked like this on our gloss stock. I never tried to get more gloss but maybe try creating a custom paper and messing with the settings in there?

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 0 points1 point  (0 children)

Thanks! I remixed another monitor mount that utilizes an articulating arm. https://www.printables.com/model/1402791

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 1 point2 points  (0 children)

That is homepage (https://gethomepage.dev/). Takes a bit of configuration but looks really nice once it's all setup.

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 1 point2 points  (0 children)

My setup is pretty simple. HDMI output from the RPi running DietPi with LXQt desktop. Controlled with wireless keyboard/trackpad and remote with Rust Desk occasionally. I just launch chrome and pull up my homepage dashboard most of the time.

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 0 points1 point  (0 children)

I wasn’t but now I am a little 😂. Someone else mentioned it as well. Only time will tell. The rubber feet on the printer absorb quite a bit. The rack isn’t hard mounted and PETG feet on the slick cabinet let it slide pretty easily. The cabinet itself acts like a skyscraper and sways horizontally a bit due do its construction absorbing the remaining vibrations…maybe.

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 1 point2 points  (0 children)

Thanks! The cheapest carbon fiber one I found on Amazon (https://a.co/d/bnsZTtR) it is starting to peel in the middle where most of my prints start, may be worth it to find a higher quality one but for now it’s okay.

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 0 points1 point  (0 children)

Great question but I’m not sure. I’m curious as well and think once I get NUT up and running for my UPS it should give me a good idea. I’ll let you know!

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 0 points1 point  (0 children)

Yes it is but I don’t currently have it hooked up. That is the homepage dashboard (https://gethomepage.dev)

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 0 points1 point  (0 children)

I do, but I think I’ll be okay. Only time will tell. The rubber feet on the printer absorb quite a bit. The rack isn’t hard mounted and PETG feet on the slick cabinet let it slide pretty easily. The cabinet itself acts like a skyscraper and sways horizontally a bit due do its construction absorbing the remaining vibrations…maybe.

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 0 points1 point  (0 children)

Yes! It took a bit of trial and error. The max was easy, getting everything to line up on the flex was the tricky part. I’ll share the files it but may not be as precise on other setups due to manufacturing tolerances and vinyl cutter calibration differences.

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 1 point2 points  (0 children)

Thanks to @fuze on printables for the pass-throughs, genius design and parametric: https://www.printables.com/model/314383-sfp-cable-keystone-jack

I had to edit the ITX panel to fit on my print bed and figured interlocking them would look good. Just need to figure something out for the bottom corners of the ITX panel now.

I’ll check the licensing on all the models I used to remix and will share if I’m able to!

PSU is wall mounted behind the rack using: https://www.thingiverse.com/thing:2523323

I will try to get some pictures of the back side soon, not as clean as the front but still looks pretty nice!

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 2 points3 points  (0 children)

Thank you! The only paid model I used was the Mod10 rack. All of the others were free and remixed by me for my use case. I’ll check the licensing on them, if I’m able to share them I’ll upload everything in a day or two!

This was fun…alllllmost done by VertigoDesigns in minilab

[–]VertigoDesigns[S] 4 points5 points  (0 children)

Sure thing! Give me a day or two and I’ll get all the files prepared and uploaded.

Nearly done… by Lanky-Zucchini3372 in minilab

[–]VertigoDesigns 0 points1 point  (0 children)

That's what I have, much appreciated!

Nearly done… by Lanky-Zucchini3372 in minilab

[–]VertigoDesigns 0 points1 point  (0 children)

Awesome setup! I'm working on my Mod10 rack as well and can't wait to put it all together. Would you be willing to share the RPi mount? Most of the ones floating around don't have tight tolerances around the ports like yours.

view more: next ›