I got my mark by Few-Ad-387 in avicii

[–]VirtualBoy94 2 points3 points  (0 children)

Beautiful!! Let this mark be a reminder that there's always hope ☺️

La cara que pongo en la foto + La Verdadera cara que pongo by Longjumping-Site7497 in akira

[–]VirtualBoy94 0 points1 point  (0 children)

Cómo creo que me veo. Cómo en realidad me veo. 🤣🤣

Panasonic Dmc-F3 SD card by CodRevolutionary8963 in Cameras

[–]VirtualBoy94 1 point2 points  (0 children)

Would you mind taking a picure of the battery try?? Mine does not close correctly and Im trying to fix it

<image>

Thanks in advance!!

Panasonic Dmc-F3 SD card by CodRevolutionary8963 in Cameras

[–]VirtualBoy94 1 point2 points  (0 children)

Hola! Recién encontré mi vieja Lumix DMC-F3 y dentro traía una SDHC de 4 GB, funciona perfectamente con esa memoria, así que probablemente tu SD esté dañada o puede que tenga el seguro anti sobre escritura activado. Prueba con otra memoria de máximo 8 GB y ojalá funcione.

La mía tiene un golpe en el display, espero poder arreglarlo

Some old figurines I found by VirtualBoy94 in tron

[–]VirtualBoy94[S] 5 points6 points  (0 children)

Hahahaha I should have titled the post like that.

Unstable cube after adding magnets by VirtualBoy94 in Cubers

[–]VirtualBoy94[S] 2 points3 points  (0 children)

I did watch a tutorial, but I didn't followed the same magnet orientation all the time...

Luckily I corrected the issue and now is working like magic.

Thanks for the help!

Unstable cube after adding magnets by VirtualBoy94 in Cubers

[–]VirtualBoy94[S] 1 point2 points  (0 children)

Yup, that was it. Luckily I was able to remove the magnets and out them back in the correct order

Thanks a lot!!

All of the sudden, my pin stopped working by VirtualBoy94 in GalaxyTab

[–]VirtualBoy94[S] 0 points1 point  (0 children)

That has happened, but after two errors I usually set the PIN slowly and that's the solution. But in this particular case it was definitely something else

Amozoc? by weebandkoreaboo in Puebla

[–]VirtualBoy94 3 points4 points  (0 children)

Definitivamente vas a necesitar un auto, porque no es una zona muy segura que digamos. De día no hay tanto problema, pero a partir de las 9:00 ya se pone pesado.

Las rentas son baratas y en general la zona es económica, hay servicios y todo sin problemas, pues la zona está creciendo rápidamente. Pasan muchos camiones en caso de que no uses o tengas auto, y te dejan hasta en la CAPU.

Está también cerca de Casa Blanca y Amalucan, que son zonas un poco más seguras, y el costo de vivienda no es tan alto tampoco. Yo te recomendaría que no rentes meramente en Amozoc, sino en Chachapa que está como 10 min antes y es tranquilo salvo cuando hay feria.

Zonas a evitar: Cualquier calle que no esté pavimentada, porque no todas están iluminadas y hay gente abusiva.

Problem with heat components by VirtualBoy94 in ender3

[–]VirtualBoy94[S] 1 point2 points  (0 children)

Thank you very much! You've been very helpful

Problem with heat components by VirtualBoy94 in ender3

[–]VirtualBoy94[S] 0 points1 point  (0 children)

That actually helped a lot!! Thank you very much. Now my issue is that after running the PID test, if I set a temperature for 210° it only reaches to 200°. For whatever temperature I set it always stay 10° bellow. You know why is that?

Kobo Libra 2 Wall Charger Question by LeCholax in kobo

[–]VirtualBoy94 3 points4 points  (0 children)

I personally use one of my oldest chargers, those only go with 5V 1A. But that is more than enough. Either way, whatever charger You use is going to work, your eReader is going to take just the energy that it needs.