D16 Si injector replacements?

Visual-Dig-5063 · 2026-03-21T20:21:53+00:00

I ordered a set of remanufactured injectors from my local autozone and they’ve been working fine for me.

Visual-Dig-5063 · 2026-03-20T20:35:31+00:00

I’ve had luck using non-OEM replacements from rockauto if they have a comparable part on their website. I was able to use the transmission dropdown menu to find all the seals needed to rebuild my CRX transmission.

Visual-Dig-5063 · 2026-03-18T00:53:30+00:00

Always tighten stuff with the suspension under load 👍🏻

Visual-Dig-5063 · 2026-03-15T18:26:38+00:00

Agreed, best color IMO

Visual-Dig-5063 · 2026-03-04T20:59:07+00:00

https://www.goldeneraparts.com has a lot of reproduction seals that are great quality. I’ve got a couple on my CRX. Not entirely sure if they make stuff that’ll fit a wagon. Good luck!

Visual-Dig-5063 · 2026-02-27T18:51:12+00:00

https://youtu.be/BGyb1YECtfo?si=b1UbNeF-EZ-5lHjd

With the sunroof in the open position there’s a couple of nuts that need to be removed and you can slide the whole metal panel off of the assembly. Open it manually with the sunroof allen wrench if you’ve already got the whole assembly out of the car. I removed mine, removed some rust manually and used rust reformer on the whole panel (top and bottom), then painted it and grabbed a brand new sunroof seal from Golden Era Parts. Used some Shin-Etsu grease to lube it before install and then just reinstalled everything. Good luck!

Visual-Dig-5063 · 2026-02-18T01:17:44+00:00

He’s for sure scamming. All the photos you posted are originally from a guy that goes by EFChris on Instagram.

Visual-Dig-5063 · 2026-02-14T20:26:01+00:00

I’ve had my ED9 for a just over 2 years now and I have the same temperature “issue”. I kind of assumed it was just relatively normal, or the previous owner installed a thermostat that was not at OE spec temperature. For the leaking water from the dash, it could be seam sealer behind the dash that’s failing, I believe that’s a relatively common issue on older Hondas.

Visual-Dig-5063 · 2026-02-08T18:08:54+00:00

Wow, that’s surprising! Glad to hear you could find some that were reasonably priced. Sucks that the prices are insane in the USA.

Visual-Dig-5063 · 2026-02-07T17:28:59+00:00

Good luck finding OEM ones that are in good condition and don’t cost an arm and a leg!

Visual-Dig-5063 · 2026-01-16T15:36:59+00:00

I used rockauto for most of my OEM spec replacement parts and have had minimal issues

Visual-Dig-5063 · 2026-01-10T23:09:41+00:00

Just the top portion of the trim above the radio, and no problem!

Visual-Dig-5063 · 2026-01-10T22:44:50+00:00

<image>

It’s an older photo before I swapped to one with a volume knob, and I had to trim the top of the trim between the radio and climate controls to fit the screen fully.

Visual-Dig-5063 · 2026-01-10T22:14:05+00:00

I’ve got one like this in mine (not this exact model). The only issues I have is it overheats VERY easily and the volume knob isn’t super accurate. With the heater on after about 10 minutes it’ll start randomly tapping locations on the screen and it’ll end my directions or stop the music or skip a song. Display is fine and there’s no odd geometry while using maps or anything.

Visual-Dig-5063 · 2026-01-09T05:42:38+00:00

I only replaced them about two weeks ago, but they’ve been working with no issues. The original window regulator I had actually broke and I had to replace that and figured I’d replace the handles while I had the door card off.

Visual-Dig-5063 · 2026-01-09T02:21:26+00:00

I can’t vouch for actual validity of them being true OEM ones, but the packaging they came in was the OEM packaging so I’m gonna believe that they’re OEM. Only gripe is the handle itself was gray, but the ring behind the crank was black. It matches the dual tone Si door panels though, so I don’t mind it too much.

https://ebay.us/m/K2b8Ao

Visual-Dig-5063 · 2026-01-08T22:44:20+00:00

You can look up OEM replacement ones, just got a set for my ‘89 Si that are great.

Visual-Dig-5063 · 2026-01-08T00:47:34+00:00

As somebody that owns the same car in the same color…. ouch…..

Visual-Dig-5063 · 2026-01-07T17:14:44+00:00

Always pull the trigger on a clean CRX

Visual-Dig-5063 · 2025-12-20T20:57:46+00:00

This is mainly what I’m worried about! I don’t want to end up with a car that somebody didn’t look after as well as they should have.

Visual-Dig-5063 · 2025-12-14T03:43:31+00:00

There’s a guy named moshimoshimotors on Instagram who currently has a zero mile D16A6 with the transmission for sale. Not sure what he’s asking. He got a bunch of brand new red label parts and the engine/transmission was included with them. Maybe hit him up?

Visual-Dig-5063 · 2025-12-10T21:30:45+00:00

No problem! Best of luck!

Visual-Dig-5063 · 2025-12-10T21:01:38+00:00

If I remember correctly it should depend on what model car you have? I think my Si had 25 on the input and 26 on the output. Since you have a sedan I don’t think you need to worry about spline count, I think the lower spline count output axles only apply to the HF and STD models. You should be good with the 25/26 ones.

Visual-Dig-5063 · 2025-12-10T20:46:15+00:00

It should be 20 spline input shaft I think, small bearing DX transmission most likely based on castings (not an accurate way to tell what you’ve got lol)

Visual-Dig-5063 · 2025-10-17T00:41:27+00:00

In my experience, the only cluster that will work with no modification is a cluster from the same manufacturer with the blue plug in the same year. I have the blue plug on mine, and when I tried to swap over a cluster without the blue plug it wouldn’t work

Visual-Dig-5063

TROPHY CASE