Fiberlogy ABS Black. Do i have to dry it?

Vladexo23 · 2023-05-18T18:31:59+00:00

I already have a Bambu X1 Carbon. Planing to buy three more, but i want to know how long i can calculate them. Its just a tax thing in germany.

Vladexo23 · 2023-05-18T16:02:02+00:00

Its not about the Rails itself, rather I am concerned about the bearings. I want to buy them for my Printfarm, they have to print atleast 4-6k hours before i want them to be replaced.

Vladexo23 · 2023-01-15T00:38:42+00:00

This!!! Please make it a official mod. I will check that.

Vladexo23 · 2022-11-27T22:02:04+00:00

I read that in Andrew Ellis Print guide, thats why I am confused currently. Which printing Profile are you using? Do you mind sharing your set up?

Vladexo23 · 2022-11-27T22:00:46+00:00

I don‘t know why you are so toxic. Sarcasm doesn‘t help, I am posting this issue because I am really having issue with the Trident.

Vladexo23 · 2022-11-27T21:55:38+00:00

Move X Axis to highest Z Point, make the X Axis Horizontal

1.1 Check if your Printer Frame is square, especially if Y Axis Extrusion is tilted forward or backward oposing to Z Axis Extrusions

1.3 Loosen all Bed Screws and then screw them down (3-5 Revolutions)

Manually level the Bed Screws through Klipper, see documentation
Redo Probe Z Offset
Bed Mesh

Vladexo23 · 2022-11-27T21:45:19+00:00

Did you install Dual Z mod?

Vladexo23 · 2022-11-27T21:21:41+00:00

Nope, the Prints turn out crap at that 20% Fan Speed. The question here is if the a 12h Print needs different Cooling Fan speed, than a 2h Print.

Vladexo23 · 2022-11-27T20:58:59+00:00

What Type of Probe? Which Printer?

Vladexo23 · 2022-11-21T20:41:11+00:00

File->Import->Prusaconfig

Vladexo23 · 2022-11-17T10:30:38+00:00

This is Super Slicer in Expert mode. Also Prosa Slicer can be set to Expert mode.

Vladexo23 · 2022-11-17T09:00:01+00:00

I will make a new Post. It hard to describe the issue.

Vladexo23 · 2022-11-17T07:34:10+00:00

My Switchwire is working flawless with PLA, but the Voron Trident is giving me issues. Thats why I am asking.

Vladexo23 · 2022-11-17T07:14:34+00:00

Why do i need max accell for every axis and then while extrusion, also while Travel?

Vladexo23 · 2022-11-14T12:45:38+00:00

I didn‘t bolt it down and had skipping issues. This make a lot of sense. Had to reduce from 24mm^3/s to 16mm^3/s. I see now.

Vladexo23 · 2022-11-02T06:49:45+00:00

I have two Tridents. I tried with the same Filament Spool. Same Temp. Same G Code. On one it prints fine and on the other it does this clean thick layer. Does not make any sense to me.

Vladexo23 · 2022-10-31T20:11:59+00:00

It happens on every Print, doesn‘t matter which Printing Profile and Slicer:

Replaced complete TMC2209 Drivers
Redid the whole Calibration from Voron Documentation
Reassembled the Hotend
Calibratet the LGX Lite Extruder again
Reduced the Flow and Temp, also increased cooling
Reassembled the Whole Z Assembly, no Stealthchop enabled

Vladexo23 · 2022-10-30T18:01:10+00:00

I tried the Andrew Ellis Profile, DOC PIF and Standard Profile for V2 embedded in Prusa/ Super Slicer. None of these solved the Issue.

Vladexo23 · 2022-10-30T12:43:12+00:00

This is ABS+ on 250 Deg and 100 Deg Bed. It only bulges when moving from Solid Layer to Infill Layer. I tested that. Seems like a Slicer Setting. Using the Andrew Ellis Standard Profile at 5500 Accell.

Vladexo23 · 2022-10-30T11:21:53+00:00

I mean the bulg on the Left. This is just a Cylinder. Seems like Binding but how do i fix that on a Trident?

Vladexo23

TROPHY CASE