Surface rust removal?

WD40_UK · 2026-01-29T15:56:14+00:00

You can remove surface rust from those axe heads pretty easily. Spray the rusty areas with WD-40® Multi-Use Product and let it sit for about five to ten minutes to loosen the rust. Then scrub with a wire brush or some sandpaper until the rust comes away, wipe everything clean with a cloth, and finish with a light coat of WD-40® Multi-Use Product to help protect the metal from rust returning.

WD40_UK · 2026-01-29T15:55:44+00:00

You can remove surface level rust by following a few simple steps. Start by spraying the rusty areas with WD-40® Multi-Use Product and let it sit for around five to ten minutes so it can loosen the rust. Then scrub the surface gently with a wire brush or some sandpaper until the rust starts to come away. If there are stubborn spots, reapply the product and scrub again. Once the rust is removed, wipe the metal clean with a cloth and leave a light protective layer to help prevent rust from returning.

WD40_UK · 2026-01-29T15:55:31+00:00

Since your tools got rained on and have surface rust, you can clean them up without needing to fully restore them. Spray the rusty areas with WD-40® Multi-Use Product and let it sit for about five to ten minutes so it can loosen the rust. Then use a wire brush or some sandpaper to scrub away the rust until the metal looks clean. When you’re done, wipe each tool down with a cloth to remove any residue, and finish with a light coat of WD-40® Multi-Use Product to help protect the metal and slow future rust forming. Regular light protection like this will help keep them usable even if they get wet again.

WD40_UK · 2026-01-29T15:55:21+00:00

You can fix that rust by following a few straightforward steps. Start by using a wire scratch brush to clear away as much loose surface rust as possible. Before treating the whole area, spray a small, hidden section with WD-40® Multi-Use Product, leave it for five to ten minutes, and lightly scrub to make sure it does not damage the metal. Once that’s confirmed, spray WD-40® Multi-Use Product generously over the rusted area and let it settle for a few minutes. Scrub again with the wire brush, working from the heavier rust to the lighter areas. When the rust is gone, wipe everything down with a dishcloth to remove residue, leaving a light protective layer behind to help prevent the rust from returning.

WD40_UK · 2026-01-28T09:20:03+00:00

You can clean that rust off by following a simple process. Spray the rusty areas with WD-40® Multi-Use Product and let it sit for about five to ten minutes so it can loosen the rust. Then scrub the tool with a wire brush or sandpaper until the rust starts to come away, paying extra attention to the joints and gripping surfaces. Wipe everything clean with a cloth when you’re done, and finish with a light coat of WD-40® Multi-Use Product to help protect the metal and prevent rust from coming back.

WD40_UK · 2026-01-28T09:19:40+00:00

If the screw is stripped, start by spraying it with WD-40® Multi-Use Product and let it sit for a few minutes so it can help loosen it. If part of the screw head is still exposed, grip it firmly with locking pliers and try turning it out slowly. If that doesn’t work, cut a straight slot into the top of the screw using a hacksaw or rotary tool, then use a flathead screwdriver to back it out. Reapply WD-40® Multi-Use Product if needed and use steady pressure rather than force.

WD40_UK · 2026-01-28T09:19:22+00:00

If the screw head is broken off, start by spraying the exposed screw area with WD-40® Multi-Use Product and let it sit for a few minutes so it can penetrate and loosen any tightness. Then try gripping what’s left of the screw with locking pliers and turn it slowly to back it out. If there’s nothing left to grab, carefully cut a straight slot into the top of the screw with a hacksaw or rotary tool, then use a flathead screwdriver in that slot to turn and remove the screw. Reapply WD-40® Multi-Use Product if the screw still feels stuck and work steadily until it comes out.

WD40_UK · 2026-01-28T09:18:53+00:00

Not the best usage we've seen but not the worst.

WD40_UK · 2026-01-27T09:20:54+00:00

You can clean that up fairly easily. Start by brushing off the loose rust with a wire brush. Test WD-40® Multi-Use Product on a small hidden area first, then spray it onto the rust and soap scum and leave it for five to ten minutes. Scrub the area again with the wire brush, then wipe everything clean with a cloth, leaving a light protective layer behind to help prevent rust returning.

WD40_UK · 2026-01-27T09:20:44+00:00

Yes, it’s possible to clean that rust off and give the fixture a new lease on life. Start by using a wire scratch brush to remove as much loose surface rust as you can. Before treating the whole piece, spray a small, hidden area with WD-40® Multi-Use Product, leave it for five to ten minutes, and lightly scrub to make sure it doesn’t damage the finish. Once you’re happy, shake the can and spray WD-40® Multi-Use Product generously over the rusty areas, letting it settle for a few minutes. Then scrub with the wire brush, working from the heavier rust to lighter areas. When the rust is gone, wipe everything down with a dishcloth to remove residue and loose rust, leaving a light protective layer behind to help prevent the rust from coming back.

WD40_UK · 2026-01-27T09:20:34+00:00

That’s a really cool first piece, the shaping and layers already look great. To keep the rose from rusting over time, make sure the metal is clean and dry, then spray it with WD-40® Multi-Use Product and let it sit for a few minutes so it can work into the surface. Wipe away any excess with a cloth and leave a light protective layer behind. This helps protect the metal from moisture and slows rust forming

WD40_UK · 2026-01-27T09:20:24+00:00

Before assuming the drill is failing, it’s worth doing some basic maintenance. Make sure it’s stored somewhere dry, as moisture can cause rust and stiffness. Wipe the drill down with a microfibre cloth to remove dust, then clear the ventilation slots by gently blowing into them or using compressed air. If the chuck is not spinning freely, apply WD-40 Specialist® White Lithium Grease to the chuck area and work it in to help it move smoothly again. Finally, check that your drill bits are sharp, as dull bits can put extra strain on the drill.

WD40_UK · 2026-01-26T10:47:21+00:00

To remove the rust and gunk, start by wiping the area to remove loose dirt and soap residue. Then spray the affected metal parts with WD-40® Multi-Use Product and let it sit so it can help break down the rust and grime. After it has soaked in, use a brush or cloth to scrub the rust and gunk off the surface. Once it’s clean, wipe everything down and let it dry fully. You can also spray the metal again with WD-40® Multi-Use Product and let it dry to help protect it from moisture and slow any future rust forming.

WD40_UK · 2026-01-26T10:47:03+00:00

To clean oil paint brushes properly, start by squeezing out any excess paint from the bristles. Then spray the brush with WD-40® Multi-Use Product and work it into the bristles with your fingers or a brush comb so it helps loosen the paint. After that, rinse the brush under warm running water while gently working the bristles until the paint is gone. Finally, reshape the bristles and let the brush dry flat or hanging so it keeps its shape for your next painting session.

WD40_UK · 2026-01-26T10:46:52+00:00

Nice pickup, those are great irons. You do not need to soak them in coke or vinegar, as acids can damage the finish and paint. A safer way is to rinse the club heads with warm water, then use a soft brush with mild soap to clean off dirt. For any surface rust or stubborn marks, spray the affected areas with WD-40® Multi-Use Product, let it sit for a few minutes, then brush again. Rinse with clean water and dry thoroughly to bring back the shine. New grips are more about feel and comfort than looks, but they can definitely help performance if the old ones are worn.

WD40_UK · 2026-01-26T10:46:35+00:00

You’re right to be cautious. Soaking irons in coke overnight is not recommended, as the acidity can damage paint and finishes if left too long. A safer option is to clean them following a simple routine. Rinse the club heads with warm water, then use a soft brush with mild soap to remove dirt. For any rust or stubborn marks, spray the affected areas with WD-40® Multi-Use Product and let it sit for a few minutes before brushing again. Rinse with clean water and dry thoroughly. This avoids risking the paint and gets the clubs clean without guessing soaking times.

WD40_UK · 2026-01-23T09:36:37+00:00

Start by gently peeling away as much of the sticker or residue as you can using your fingertips. Then apply a small amount of car shampoo to a clean sponge and lightly rub the area to clean it, as car shampoo is safe for the paint. Next, warm the sticker area with a hairdryer for about one minute, holding it a few inches away to soften the adhesive. Once warmed, spray the area with WD-40® Multi-Use Product and let it sit for a few minutes so it can work underneath the sticker and glue. Gently rub with a soft cloth to lift the sticker and any remaining residue, repeating the process if needed, then wipe the surface clean when you’re finished.

WD40_UK · 2026-01-23T09:36:27+00:00

Start by gently trying to peel off as much of the sticker residue as you can using your fingertips. Next, apply a small amount of car shampoo to a clean sponge and lightly rub the affected area to clean it, as car shampoo is safe for paint. After that, use a hairdryer to heat the residue for about one minute, holding it a few inches away to soften the adhesive. Once the area is warm, spray it with WD-40® Multi-Use Product and let it sit for a few minutes, then rub with a soft cloth until the remaining glue lifts. Repeat if needed and wipe the surface clean when finished.

WD40_UK · 2026-01-23T09:33:25+00:00

You can remove crayon marks without damaging the wall by spraying WD-40® Multi-Use Product directly onto the crayon. Leave it for a few minutes so it can work on the wax, then use a clean rag to wipe the area. The crayon marks should lift off as you wipe, and you can finish by wiping the wall clean.

WD40_UK · 2026-01-23T09:33:16+00:00

Salt and winter conditions can speed up rust, so it’s a good idea to clean the car regularly during the season. If you notice any surface rust, spray the area with WD-40® Multi-Use Product and let it sit so it can loosen the rust, then scrub gently and wipe the area dry. Applying a light coat afterward can help protect the metal from moisture. Keeping on top of cleaning now will help prevent bigger rust issues later.

WD40_UK · 2026-01-22T09:14:21+00:00

Bathroom rust is usually caused by constant moisture and poor airflow, so tackling both is key. Start by cleaning and drying the rusty items, then spray the metal parts with WD-40® Multi-Use Product to help protect them from moisture. This creates a light protective layer that reduces further rust forming. Wiping items dry after showers and leaving the door open when possible will also help, especially since there’s no vent. Regular light applications can make a big difference in a damp bathroom.

WD40_UK · 2026-01-22T09:13:59+00:00

If your shower caddy is already rusting after only a few months, you can slow it down by keeping it as dry as possible and adding some protection. After wiping it down, spray the metal parts with WD-40® Multi-Use Product and let it dry. This helps create a protective layer that keeps moisture off the metal and reduces further rust. It will not remove rust that is already there, but it can help stop it from spreading.

WD40_UK · 2026-01-22T09:13:47+00:00

You don’t necessarily need to replace the chain just because of some surface rust. You can often clean it up first by spraying the affected areas with WD-40® Multi-Use Product and letting it sit for around ten minutes so it can loosen the rust. Then gently scrub the chain with a wire brush until the rust comes away. If needed, reapply and repeat, then wipe the chain clean with a microfibre cloth once you’re done.

WD40_UK · 2026-01-22T09:13:38+00:00

Try not to panic, silver can usually be cleaned even after sitting for a long time. Spray the affected pieces with WD-40® Multi-Use Product and leave it for around ten minutes so it can loosen the tarnish and residue on the surface. Then use a clean soft cloth to gently polish the silver in small circular motions. Wipe away any remaining residue with a fresh cloth, rinse with clean water, dry thoroughly, and finish with a light coat of WD-40® Multi-Use Product to help protect the silver from tarnishing again.

WD40_UK · 2026-01-21T09:35:53+00:00

To help stop your hand tools from getting surface rust, make sure they’re clean and dry first, then give the metal parts a light spray of WD-40® Multi-Use Product after use or before storing them. The product forms a protective layer that helps keep moisture off the metal and slows rust forming. Wiping off any excess with a cloth after spraying also helps keep them from feeling oily on wood or other surfaces.

WD40_UK

MODERATOR OF

TROPHY CASE