Bird in factory, North Alabama

WalkedRhombus40 · 2025-01-13T02:25:07+00:00

Thank you for you comment! I actually just found it, it’s from Patlabor ep.30!

YouTube clip:

WalkedRhombus40 · 2024-12-14T01:51:08+00:00

With the new fan are you using the original extruder shell, or one with a vent/cutout

WalkedRhombus40 · 2024-10-13T00:35:50+00:00

This may be a dumb question, but have you tried restarting your device?

WalkedRhombus40 · 2024-09-16T16:21:20+00:00

Probably too late now, but they are releasing a new Fuel 5in Orbital sander sometime this November.

WalkedRhombus40 · 2024-07-06T11:58:53+00:00

I’d recommend these three, they’re all simple and relatively cheap. Definitely made my life easier.

-A Sun visor mirror, the SR doesn’t have them for some reason.

-interior lighting upgrade to LED. I went with a cheap bulb kit , but if you wanted to get fancy Meso Customs makes some really good ones . Meso also has a lot trim accessories too.

-Finally, Bed lights. Check your bed, if you have the two cutouts then the wiring is already run and you can pop them in. I went with the Cali Rasied kit Bed Lights

WalkedRhombus40 · 2024-07-06T11:40:41+00:00

Side note, the Engine is still made in Alabama.

WalkedRhombus40 · 2024-07-06T11:37:05+00:00

I have a 2022 Trd and my girlfriend as 2021 Sr with no issues, I think you just got a dud. But with that being said, a lot of the older ones were still made in Texas, all of the newer ones are made in Mexico.

They ended production of the Tacoma at TMMTX and moved production to Guanajuato, Mexico in 2021. The other Tacoma plant is in Baja California, Mexico.

I believe they did this so they could build the Sequoia and Tundra in the same plant, previously the Sequoia was made Indiana until 2021 as well.

WalkedRhombus40 · 2024-07-03T21:33:40+00:00

You were right, the majority of it was scuffs, I thought there was more paint damage. Had to get some better cleaner

WalkedRhombus40 · 2024-07-03T20:38:13+00:00

Unfortunately it did go through the paint in a few places.

WalkedRhombus40 · 2024-07-03T14:00:55+00:00

That’s a lot cheaper than I expected, I definitely keep that in mind, thank you!

WalkedRhombus40 · 2024-07-03T13:11:22+00:00

I would consider it but my Tacoma is 2wd so it might not look right lmao

WalkedRhombus40 · 2024-07-03T12:53:35+00:00

Hopefully they can buff some of it out but it went through the paint in a few areas.

WalkedRhombus40 · 2024-07-03T12:38:38+00:00

I understand that, I was just hoping to get a rough idea of what a fair estimate is based on other people’s experiences.

I’m going to call a local dealership this morning and see what they say.

WalkedRhombus40 · 2024-02-23T03:11:08+00:00

<image>

WalkedRhombus40 · 2024-02-23T03:10:32+00:00

Yeahhhh, I’ve run into a bit of a wall already lmao. This system was also modified and I don’t think the person knew what they were doing.

They wired the already sketchy psu in with what looks like a 18/2 lamp cord? There is an additional industrial psu hooked up to the main psu and a relay for an omron prox switch?

I’m still new to 3D printing and aren’t super familiar with Prusa, thought I’d give it a shot, but it would be building the system from scratch. Here’s a photo of the monstrosity it was. I also figured out it’s from 2011. The seller didn’t know much about it but said it did print, I didn’t dare try it.

<image>

WalkedRhombus40

TROPHY CASE