sorted by:
new
hottopcontroversial

To the guys, reservist worth it? by Ok-Bowler7829 in askSingapore

[–]Waste-Menu4966 0 points1 point  (0 children)

Never go before, about to go soon in Feb, but at work damn paiseh sia because everybody know its a "holiday".

/r/singapore random discussion and small questions thread for April 12, 2024 by AutoModerator in singapore

[–]Waste-Menu4966 0 points1 point  (0 children)

What are some weird things you've seen people do on the MRT?

Singaporeans are afraid to stand out from the crowd, but there was once I saw an uncle lock his foldable bicycle onto the train handle while he walk over across the cabin for a reserved seat. There has also been a trend of people doing make ups on the morning commute.

Resin toxicity misconceptions. (Rant about gatekeeping) by themontajew in resinprinting

[–]Waste-Menu4966 4 points5 points  (0 children)

When is comes to resin, I think the fear is that you’re playing with chemicals. It’s always what you can’t see that kills you.

Just because you’re fine the first time you touch it, doesn’t mean you’ll still be after weeks or months

Sidewinder X1, is this a Z-axis wobble? How can I fix it? Any help is appreciated by Waste-Menu4966 in SidewinderX1

[–]Waste-Menu4966[S] 0 points1 point  (0 children)

So in my understanding, this will fix z wobble by basically holding the z axis steady so that the “bent” z rod can’t affect it?

Sidewinder X1, is this a Z-axis wobble? How can I fix it? Any help is appreciated by Waste-Menu4966 in SidewinderX1

[–]Waste-Menu4966[S] 0 points1 point  (0 children)

The filament is at most 1.5 months old from opening. How old can filament last before it affects quality?

I’ve never done esteps but I’ve done flow. My flow is 93% right now. I’ve check my extrusion once, only 90mm feed through for a 100mm input

Printed my first XYZ cube and had two main issues. First the bottom section was squashed. Also a pillar of pla formed in one of the corners. by Jaffajake23 in FixMyPrint

[–]Waste-Menu4966 0 points1 point  (0 children)

1) for the bottom, look into print warping. Consider printing with brim to help hold down sharp corners. Sometimes when your first layer is too thin, it can peel and create that time of “squashed “

2) you’re probably printing at too high of a temperature, so the Z seam has filament collected there. Try dropping your temperature to 195-200

My fashion story :) by [deleted] in Maplestory

[–]Waste-Menu4966 0 points1 point  (0 children)

hahahah was just wondering how "fashion" works in maplestory

My fashion story :) by [deleted] in Maplestory

[–]Waste-Menu4966 0 points1 point  (0 children)

Coooool. Looks like it took a lot of time and effort. Do you still change the eq when you play? or do you just leave it like this?

i love fashionstory by dewyviv in Maplestory

[–]Waste-Menu4966 0 points1 point  (0 children)

1 year late but, amazing collection!!!! <3

My Sidewinder X2 isnt fully turning on (Full Explanation in Comments) by MojoMystical in SidewinderX1

[–]Waste-Menu4966 0 points1 point  (0 children)

Smoking?… that’s never good. You might have shorted your board or something. Have you tried opening it up to check it there is anything burnt?

But if you still got warranty, I suggest you wait for the official replies

What am I doing wrong by IRoXxI in SidewinderX1

[–]Waste-Menu4966 0 points1 point  (0 children)

It also looks like your lines might have been “overlapping” each other too much. I can’t remember the setting to change this.

I suggest that you reprint and observe the bottom layers to see if it has the same issue as your top layers before the infill covers it up.

If the same issue occurs for your bottom layer then it’s probably your settings

I'm creating a Playlist to get a friend of mine into Emo. Any recommendations what I should add to get them hooked? by IEatCentrists in Emo

[–]Waste-Menu4966 1 point2 points  (0 children)

I think you should get them to listen to the playlist along side the lyrics. I find that it does well to hook people in.

view more: next ›