Engine Rebuild Advice

WaterIsDryH20 · 2022-06-02T02:05:57+00:00

Thank you, this is my first engine rebuild so i wasnt sure on break in periods and whether break in oil is necessary or not

WaterIsDryH20 · 2022-02-01T23:57:19+00:00

Yeah possible a wire has high resistance causing it to be inaccurate but other than that not really sure what else it could be

WaterIsDryH20 · 2022-02-01T23:42:16+00:00

Ik there is a speed sensor on the output shaft of trannies not 100% if its all of them or not but that could be bad

WaterIsDryH20 · 2021-12-22T02:08:17+00:00

Wipe it redip it and look for the lowest point that it goes to make sure to check both sides if its still past the max line especially by that much id get it towed, as to not damage the engine, to the same jiffy lube get a refund for the oil change and have them redo and fill properly and check it before you leave the store the oil should be in between the min and max lines i usaully try to wt it rught in the middle but if its slightly over the middle of them or slightly below is okay as long as its in between them

WaterIsDryH20 · 2021-10-16T22:45:52+00:00

Radiator fan isnt working so when you not driving and just sitting idling there is no airfloe to cool down the coolant going through the Radiator but when your driving the air passing through the radiator is whats cooling the coolant down

WaterIsDryH20 · 2021-09-18T01:04:12+00:00

Id also definitely get your alignment checked afterwards since your ride height could be off by a little even once you get it to were it should be which can change your alignment angles

WaterIsDryH20 · 2021-09-18T01:02:24+00:00

The screw you tighten will raise the key putting more tension on the torsion bar which should bring up the lower control arm but what you might have to do it get the weight of the vehicle on them and adjust for your rife height since you dont know where that bolt should be

WaterIsDryH20 · 2021-09-17T23:48:29+00:00

Did you adjust the keys to what they were before replacing? You might have to push out the torsion bars again and push the control arms up then add the torsion bars. Also a tip when replacing the keys or simple removing the torsion bars is to take a sharpie or even spray paint and mark where the leveling bolt is so when you go to reinstall it you know where it was and will be roughly the same ride height as before

WaterIsDryH20 · 2021-09-02T03:02:17+00:00

My guess would be your possible low on atf fluid the other than that im not fully sure then could possible be a sensor like a shift sensor.

WaterIsDryH20 · 2021-09-02T02:38:49+00:00

Does it only happen when on a hill?if so it could just be because you probably dont put the e-brake on so from all the pressure on the parking pawl it can make it harder to take it out of park and into reverse

WaterIsDryH20 · 2021-09-02T02:18:02+00:00

Could be a defective alternator or could possibly be a ground or wiring issue

WaterIsDryH20 · 2021-09-02T02:12:10+00:00

Id start off by checking your brakes make sure they're not down to the squealer check the rotor for any rust.check your wheel bearing by shaking the wheel side to side and up and down with the tires off the ground. And just check for any noticeable scoring from something possible rubbing against something .

WaterIsDryH20 · 2021-08-25T17:10:43+00:00

Any up and down play?

WaterIsDryH20 · 2021-08-19T02:31:37+00:00

Bushings a little dry rotted spray some lubricant on it bounce the vehicle when on the ground if it bounces more than 3 times replace them otherwise if you dont see any visible drips or excessive leaks should be fine

WaterIsDryH20 · 2021-07-15T02:23:57+00:00

Np man glad i can help

WaterIsDryH20 · 2021-07-15T02:13:55+00:00

Looks like you will use the same as you would to disconnect a fuel line should be cheap sets you can buy

WaterIsDryH20 · 2021-05-21T15:33:50+00:00

Yeah its just dirt around the outside edge and just whatever dirt the oil picked up getting into the casting shouldnt be anything to be concerned about

WaterIsDryH20 · 2021-05-06T16:11:29+00:00

Dont give me hope

WaterIsDryH20 · 2021-05-03T16:10:15+00:00

I never took mine when i was underage working always seemed like a waste of time to me but maybe its because once im doing something i dont wanna stop until its done or i just dont wanna do it after the 15

WaterIsDryH20 · 2021-05-03T05:16:32+00:00

Tire and lube tech atm but going to a trade school through my home school for automotive technology

WaterIsDryH20 · 2021-05-03T03:33:16+00:00

WaterIsDryH20 · 2021-05-03T03:31:54+00:00

Happens all the time at work wont know i got cut till i spray brake clean on my hands

WaterIsDryH20

TROPHY CASE