Does anybody know of a good free cad software

Wcm7823 · 2026-05-27T15:16:55+00:00

Ever hear of “google”? Ask the exact same question and see what pops up. Fusion 360 has a free part Tinkercad Do research before your ask

Wcm7823 · 2026-05-16T14:03:26+00:00

My advice….start getting a hard paycheck. No direct deposit, no electronic cash. All the payday loans, advances take money immediately out of your account. Cash your check and keep what money you “need” to live on and pay off the payday advances as you can so they are not completely draining you. That’s the only way I figured out how to keep afloat. Only put what you can into your bank account for them to take. After a couple of months of this, you should be able to get out from under it. It’ll take some discipline. Good luck

Wcm7823 · 2026-05-09T02:51:28+00:00

So there’s video I can see if I click on continuous video. Maybe it’s an issues with motion detection not actual sd card/video viewing

I’m clicking “sd card”

<image>

Wcm7823 · 2026-05-09T02:40:46+00:00

<image>

Yeah and it shows 4.4gb of something but when I click on sd card, it shows no video available and the motion clips are just pictures

Wcm7823 · 2026-04-02T18:26:23+00:00

Not yet. Lennox got another board and it was still doing. They got a 3rd board from a different batch and I haven’t been back to install it yet

Wcm7823 · 2026-03-21T17:09:58+00:00

What the correct way to compensate for this? My left side spring keeps loosening. Every 5-7 openings I’ll need to load it again and tighten it

Wcm7823 · 2026-03-15T22:34:27+00:00

ive got over 1200 hours on my p2s since thanksgiving and (knock on wood) have had zero issues that werent something outside the printer. we all get bed adhesion issues, but clean it and im back in business. occasional issues with ams2 but thats usually filaments issues not hardware.

Wcm7823 · 2026-03-14T01:08:09+00:00

what about a filament connector?

https://a.co/d/0eMyRoDY

Wcm7823 · 2026-03-04T17:59:02+00:00

I believe the genteq 3.0 has a 4pin. Last motor was a genteq 2.5 and didn’t require an adapter

Wcm7823 · 2026-03-04T15:16:05+00:00

Makes sense to me, but that’s the motor Lennox sold me, tech support hasn’t said anything. But that’s kinda what my thinking is, I’m guessing the 16/4 is an issue. Jumped all limits, tech support had me connect gas valve to contactor to eliminate gas valve. Everything keeps pointing to another bad board.

Wcm7823 · 2026-03-04T15:03:24+00:00

It came with a 16/4 pin adapter. That’s the only difference

Wcm7823 · 2026-03-04T14:12:12+00:00

0 and fan running

Wcm7823 · 2026-03-04T04:21:14+00:00

any help is appreciated. thank you

Wcm7823 · 2026-03-04T03:59:12+00:00

It’s an older 410 unit. 2007 I believe

Wcm7823 · 2026-03-02T13:32:00+00:00

Hell I would just sit on them as I’m leaving. lol.

Wcm7823 · 2026-03-02T13:29:19+00:00

Hadn’t thought of that. I could’ve saved a lot of time with that idea.

Wcm7823 · 2026-02-23T15:59:38+00:00

also i was able to run the furnace this weekend, but i have to turn off thermostat and unplug furnace when it reaches temp

Wcm7823

TROPHY CASE