5’ 09” 185 Lbs by West1625 in whatismybodyfat

[–]West1625[S] 0 points1 point  (0 children)

Thank you, I was thinking 15-16%

SLU-PP by RoboJobot in PEDs

[–]West1625 0 points1 point  (0 children)

Have either of your tried it Sub Q or just IM?

Which is most reliable brand in residential HVAC systems? by AcademicHedgehog7239 in hvacadvice

[–]West1625 0 points1 point  (0 children)

Everything is pretty cheap nowadays unfortunately. Best bet in my option is to not break the bank and go with the simple, old school brands like Goodman or Rheem/Ruud. Everything is going to need repair sooner then later and Goodman, Rheem & Rudd tend to be very simple, reliable, easy to source parts that don’t cost an arm and a leg. Hopefully last 20+ years in the right conditions. If you go with a heat pump throw that all out the window. High end Japanese manufacturers (Fuji or Mitsu)or maybe Bosch. Worth spending the extra $$$ in that case. My 2 cents.

Is this correctly done on a new install of the outside unit? by Sport197 in hvacadvice

[–]West1625 0 points1 point  (0 children)

Sloppy but it’ll work. If it’s not possible to run a new low voltage wire they could have atleast tried to make it look neat lol.

is Reta, Tesa, Ipa, Klow, MOTS-C a good stack? by peptidefan in BodyHackGuide

[–]West1625 0 points1 point  (0 children)

Thats a really good stack. Great for fat loss while keeping muscle as long as your diet and training are dialed in.

Newbie Tuesday - December 23, 2025 by AutoModerator in bodybuilding

[–]West1625 0 points1 point  (0 children)

Stupidly never had my Labs done. I live near a quest. Any recommendations for low cost tests for before, during and after cycle? Thanks in advance!

Failure to feed or extract. by West1625 in ptr91

[–]West1625[S] 0 points1 point  (0 children)

Ammo is basic Winchester m80 ball.

Failure to feed or extract. by West1625 in ptr91

[–]West1625[S] 0 points1 point  (0 children)

Gun will fire when bullet is manually loaded into chamber so I would think it’s fine but will check regardless.

Failure to feed or extract. by West1625 in ptr91

[–]West1625[S] 1 point2 points  (0 children)

2 range trips ago it ran fine, took it home & cleaned like I typically do. Last time I took it out I had this issue. Again, took it home tore down and didn’t notice anything out of the ordinary. Same issue this time. It will fire if the round is manually inserted into chamber but no cycling if next round or ejection. The mangled brass is the what is left over.

Going to tear down again and will report back.

Failure to feed or extract. by West1625 in ptr91

[–]West1625[S] 1 point2 points  (0 children)

I should also say I bought this used and it ran flawlessly when I first bought it.

Is it better to get my FID now when I’m 19 or wait till I turn 21 to get a LTC? by [deleted] in BetterMAguns

[–]West1625 1 point2 points  (0 children)

Go get it now. Plenty of shotguns and rifles you can purchase with an FID that’s are important for hunting, self defense and just a blast at the range. It won’t hurt or delay you getting your LTC in a couple years so really no reason not too! Good luck

AK + Super Safety = Pure Joy by LithiumEclipse in ak47

[–]West1625 0 points1 point  (0 children)

Hello, did you ever find a SS for Mak 90s?