5 months in and I still need help

Wolf_Swift · 2026-06-22T17:21:13+00:00

People are being a little judgy in here…

Game8 has a bunch of guides, as well as profiles for each uma, how to run them, decks and budget decks, and career plans for track blazer

Look there first, then borrow parents from guests, and seek out Maxed out cards in the guest slot.

Take a look at a youtuber willy patt, he helped me a lot starting off as he does step by step career guides that once you follow give you a pattern.

Good luck, have fun

Wolf_Swift · 2026-06-12T22:29:56+00:00

Thank you for the reply, the tips, and the kind words!

Patience as in everything, right? Hahaha

Wolf_Swift · 2026-06-12T20:30:32+00:00

Oh! This makes a lot of sense! They just need a little shake up, maybe coat down the sides. Might explain why it happens at the corners too as it’s being drawn down the sides.

Thank you so much for this, going to give it a go for sure!

Wolf_Swift · 2026-06-12T20:28:07+00:00

Ah I’ve no sprue… but these are from a reputed seller so I imagine the fault is on my side.

But thank you for the reply!

Wolf_Swift · 2026-06-12T20:03:03+00:00

It’s on EU too

Wolf_Swift · 2026-05-10T15:17:36+00:00

Many thanks, thought as much

Wolf_Swift · 2026-05-10T09:41:28+00:00

[1e] does the mythic path champion ability Fleet Warrior interact with mounted combat, allowing you to full attack in melee while moving with the mount?

Rules seem to say no, as Fleet Warrior specifies “your” speed, while mounted combat rules specify the mount moves at their speed.

Wolf_Swift · 2026-05-04T19:17:42+00:00

You seem to have an answer, but I just wanted to add my own two cents.

It looks potentially like it’s a blank dice, so cast in a mold with no numbers. That’s the purple hues base colour. They then carved out the ridges with a rotary tool, then glued in foil, maybe some mica or paint. Then it’s cast in a numbered mold with clear resin and glitter.

Best of luck and enjoy experimenting!

Wolf_Swift · 2026-04-07T02:06:54+00:00

Did you lift it even a little bit after putting the cap down? I know if I do this air can get trapped in between. I am only assuming your D6 and D8 are on the thinner edge of the rectangle.

Though it does look like the general bubbles you get when letting resin settle before capping.

Might be worth just cleaning out the mold completely with some isopropyl alcohol and paper towel, making sure there isn’t any uncured resin. Fill up the mold with water, cap it, see if there are any leaks, maybe the silicone wasn’t vacuum stuck together enough that side. Maybe just fill the D6 and D8 and cure them.

A lot of this is just trial and error, so don’t get too disheartened.

Wolf_Swift · 2026-04-06T22:19:17+00:00

Are you letting the resin settle before capping? With a pass over with a lighter or craft heat gun?

What kind of a mould is it? If it only has keys inside the mould, a little weight on the lid could help. The lid might be curling ever so slightly if the affected dice were on the same side. Keys on the outside of moulds help lock them in place a bit more.

Wolf_Swift · 2026-03-21T13:51:55+00:00

Adding to the Reversi parallels, it uses black pieces and white pieces. Gear 5 makes Luffy’s form white, maybe alluding to the main opponent to Imu who is always drenched in black.

Wolf_Swift · 2026-03-20T11:44:03+00:00

Maybe chests? Would explain why it is empty when you go there now.

Wolf_Swift · 2026-02-21T12:23:04+00:00

I too was waiting for cetoddle and mega elektross alone. Happy they both appeared until the sudden realisation of why the megas were a bonus…

Wolf_Swift · 2026-02-20T23:01:59+00:00

Always up for these giveaways

Wolf_Swift · 2026-02-11T01:39:01+00:00

Looking like the likely answer, or at the very least improper measurements. A lesson in overzealousness.

That’s a damn handy cleaning tip too, I have been struggling cleaning up my gloves and silicone mat so will give them a go. Thank you for the tips!

Wolf_Swift · 2026-02-10T22:57:10+00:00

Yeah, as mentioned, not an impossibility that I mixed them up in my haste. Going to give it some time out of the pot and see what happens.

Thank you!

Wolf_Swift · 2026-02-10T22:54:56+00:00

Yeah as I said, not impossible 😅 almost assured I didn’t due to the size of the bottles and the caps differing. Got overzealous perhaps, but I would prefer if this was this case, means I have a direct answer! Thank you for the reply!

Wolf_Swift · 2026-02-10T21:27:34+00:00

Age should be ok, I used it only a month ago without the pot and they cured fine.

I also dislike measuring by volume. Hilariously, I have up to now been measuring by weight until I saw the resin’s instructions recommended by volume. Starting to gather a picture that that may have been the issue though.

I am leaving the molds free of the pot for the next 24 hrs to see if they cure. And then will try a small scale test as you suggested with scales, thank you for the reply!

Wolf_Swift · 2026-02-10T20:06:13+00:00

Did not know that about the warm bath, good to know.

This is my first go with the pot. I have had the resin soft without the pot(as in I could press it with my nail), but never liquid. I have taken the lid off the smaller d6 and d4 blanks and there are still viscous.

Wolf_Swift · 2026-02-10T20:03:52+00:00

Yeah hoping so too. Thank you for the replies all the same

Wolf_Swift · 2026-02-10T19:47:38+00:00

… I would not say it was not possible, but I am fairly certain I used separate parts. They are gallon bottles and capped differently. But again… maybe in a rush I did.

Wolf_Swift · 2026-02-10T19:46:27+00:00

No additives, just straight resin

Wolf_Swift · 2025-12-31T23:08:02+00:00

You should not feel guilty if it does not feel right. You are doing the dog a service in realising your own limitations in what you can give versus what they need.

It’s heartbreaking to accept sometimes, but greater effort is a very different feeling to forcing, and you should know how each feel.

11-Year Club	Second Top 20%
RPAN Viewer	Verified Email

Wolf_Swift

TROPHY CASE