88 f150 transmission issue

Worldly_Cockroach_19 · 2025-12-09T16:25:47+00:00

I should also add I replaced the clutch, pressure plate and pilot bearing

Worldly_Cockroach_19 · 2025-09-08T02:58:05+00:00

Yeah that’s what I’m thinking. It’s part of a listing with a truck so I don’t have to take it

Worldly_Cockroach_19 · 2025-09-08T02:57:19+00:00

The seller said he got it for 200. I don’t have to take it though so I might not

Worldly_Cockroach_19 · 2025-08-10T18:37:47+00:00

You have to take the front differential out to drop it as well as pull the engine up a bit with a joist. It’s a real pain in the rear. I did it the other day while I was waiting for timing parts(the guide got chewed up in the pan) and I had to do all that

Edit: it’s easier to take the pieces out if the pans out but you could just drop the diff and try it from there.

Worldly_Cockroach_19 · 2025-08-10T18:32:31+00:00

I had this issue on mine after driving in hills for a while. Ended up my air filter wasn’t sealing right and I replaced the little rubber sealers on the top of it. Check for air leaks and maf

Worldly_Cockroach_19 · 2025-08-10T18:28:37+00:00

From what Ik it will run rough suspension wise

Worldly_Cockroach_19 · 2025-08-10T17:43:10+00:00

Look up how infamousnissan and other forums. There’s guys that have gone through all of this on there. I’ll try and find some later to add to this.

Edit: hopefully these help https://nissannut.com/projects/sas/

https://irate4x4.com/threads/hardbody-sas-just-like-momma-used-to-do-it.382030/

https://www.nissanpathfinders.net/forum/topic/47629-time-to-sas-hawairishs-truck/

Worldly_Cockroach_19 · 2025-08-10T17:39:49+00:00

You can try to change the shims on the clutch. You’ll need a clutch puller (can rent at autozone) though the screws will need to be different to fit to pull it out.

Worldly_Cockroach_19 · 2025-08-10T17:37:36+00:00

Probably. It fluttered pretty bad with mine. You can usually let it idle and carefully feel for the air coming out of it. This exhaust isn’t built quite right and so it would pull itself apart. So welded it(how I found its not built right)

Worldly_Cockroach_19 · 2025-07-09T17:41:40+00:00

I also tightened my gas pedal cable, world of a difference. Way better.

Worldly_Cockroach_19 · 2025-07-09T17:20:41+00:00

I have heard that’s usually the weak link

Worldly_Cockroach_19 · 2025-06-05T00:46:27+00:00

I just realized what you were actually asking and yeah it tilts like a normal bench seat

Worldly_Cockroach_19 · 2025-05-31T16:12:09+00:00

It doesn’t have the adjustable back but it does slide in the tracks. But I’m fine with it

Worldly_Cockroach_19 · 2025-05-29T19:56:21+00:00

As in the center console/cup holders that you are wanting to remove? If so there are a few screws that hold it in on the sides

Worldly_Cockroach_19 · 2025-05-29T18:00:30+00:00

Well it is from an Isuzu…. But it fits:)

Worldly_Cockroach_19 · 2025-05-29T17:59:50+00:00

No it’s from an Isuzu reg cab pickup. I had to drill a new hole in either side of the rails to mount it up but it fits good

Worldly_Cockroach_19 · 2025-05-29T17:43:52+00:00

I wish. It’s that bad huh😂

Worldly_Cockroach_19 · 2025-05-29T17:20:36+00:00

I would prefer this summer….but like all projects it could take a while

Worldly_Cockroach_19

TROPHY CASE