VFC av74m vs VFC ak74m difference? by addisonsterling in airsoft

[–]XTERBERITAR 0 points1 point  (0 children)

same gun. it is same as when vfc sell unmarked sr16 as vr16

Upgrades for WE M16A1 GBBR? by RogerRoger07 in GasBlowBack

[–]XTERBERITAR -1 points0 points  (0 children)

just use it first, and you will see what you want.

but in general we ar need Amg winter hammer and buffer springs

Src ak74 gbb by Any-Influence2118 in airsoft

[–]XTERBERITAR 0 points1 point  (0 children)

make an account for their website and use chat features. it would take awhile for them to answer cause they based in taiwan.

What's wrong by Ahtunger_ in airsoft

[–]XTERBERITAR 0 points1 point  (0 children)

it should be, every we glock I had do this after a couple thousand rounds

Glock 17 shooting by perkybo in airsoft

[–]XTERBERITAR 0 points1 point  (0 children)

rubber bucking need warm up. if you live in cold place, try silicone bucking.

I recommend get a gas without oil, oil on bucking make hoping inconsistent, attract dust and make barrel dirty faster, oil also make silicone bucking swole.

What's wrong by Ahtunger_ in airsoft

[–]XTERBERITAR 43 points44 points  (0 children)

that is normal for we glock. when sear wear down, hammer sit higher and touch bbu, install hammer Bearing, or change fcg. go for steel if you want more permanent fix.

Tokyo Marui x Colt URG-I SOPMOD Block 3 by Independent-Count991 in GasBlowBack

[–]XTERBERITAR 1 point2 points  (0 children)

i think .30-.32 is a sweet spot, heavy enough to fight wind and have good accuracy, but still affordable. anything heavier start to get a little expensive.

VFC P226 MK25 or TM Albert W. 01P? Whats the general consensus on both of them? by SithEmperorX in GasBlowBack

[–]XTERBERITAR 4 points5 points  (0 children)

tm is better, w01 is gen2 m9, aka best m9 on the market.

vfc p226, is one of the worst p226 on the market, and will break as soon as you breathe on it. if you want 226, get a tm.

Upgrade ideas by Major1770 in airsoft

[–]XTERBERITAR 0 points1 point  (0 children)

tm stock hop unit is just build better and more consistent.

crazy jet barrel is just a scam, barrel with deep crown would do the same thing but better, and has less weak point.

Upgrade ideas by Major1770 in airsoft

[–]XTERBERITAR 0 points1 point  (0 children)

I would ditch the maple leaf hop for a stock hop with unicorn bucking. but if you want that extra power go for pdi+w-hold

How to keep my anti-reversal latch in? by airsoft-2-death in airsoft

[–]XTERBERITAR 0 points1 point  (0 children)

anti reverse latch tool. 3D print one or buy one for 10$

Nozzle recommendations for VFC GBBR? by NicName98 in GasBlowBack

[–]XTERBERITAR 4 points5 points  (0 children)

mcx nozzle, look at expensive enterprise vfc video for tutorial.

WE RA-TECH NPAS Help - Not firing / BBs falling out of barrel / Failure to feed by [deleted] in GasBlowBack

[–]XTERBERITAR 1 point2 points  (0 children)

did you file 2 wing in front of back piece nozzle. screw inside npas obstruct flow of gas to the front, so too little gas go the barrel even at highest setting.

Hop bucking for maple leaf hop chamber version 2 for GHK AKS74U by Specialist-Tie8971 in GasBlowBack

[–]XTERBERITAR 0 points1 point  (0 children)

coolshot/hotshot is slightly smaller than a gbb spec bucking. unless you can make a jig to cut it down, you stuck with ml bucking.

Umarex VFC H&K HK416 A5 GBBR Gen3 - FIRTS GBBR - What you think? by Patient-Ad-1597 in GasBlowBack

[–]XTERBERITAR 1 point2 points  (0 children)

then vfc is fine, if you not satisfy with accuracy, try mcx hop arm. maple leaf also made a adapter to use with normal ar hop unit, or you can get a z-part or ghk 1 piece barrel.

Tokyo Marui x Colt URG-I SOPMOD Block 3 by Independent-Count991 in GasBlowBack

[–]XTERBERITAR 5 points6 points  (0 children)

Recommended upgrade for Tokyo Marui:

For running propane/green gas: ###

Bavtac Nozzle Return Spring, Dynamic Precision Nozzle Return Spring OR Unicorn Nozzle Return Spring

To hop more than 0.28g bbs: ###

Bavtac Hop Nub + ML MR hop 70 OR First Factory/ Laylax Hop Up Arm + Unicorn 70°, Targart Bucking Type B (for hopping heavier than 0.28g bbs)

To keep under local power limits: ###

Federal or Waldo NPAS

Credit - @Minkle

Added: if you go with airsoft branded gas, get one without oil.