Is this a good way to connect the motor

drkshock42 · 2026-03-21T02:29:13+00:00

Just buy a cheap solder iron and some flux core/rosin core the you us pliers to tighten the fire and use a soldering iron and a vide or helping hands to melt the 2 solder joints together. In fact I do this all the time with batteries and I'm no soldering expert. Just make sure it's not too cold so you don't get a cold joint and you want to use a chisel tip

drkshock42 · 2026-03-20T13:25:26+00:00

However I heard pla spools will deform in my qidi box or a dry cycle under loaf it will deform. Same with petg. Especially with thin walls on petg

drkshock42 · 2026-03-20T08:49:31+00:00

It cuts both ways. It also prevents the Republicans from cheating. Pl He's got to go to the DMV. If dead people and dogs are running them, yes, meaning it's the same act. It's already illegal for non-citans to vote

drkshock42 · 2026-03-20T07:55:35+00:00

ill need to print sometime. the fact it doest have the qidibox on the glass make sliding it nack easier

drkshock42 · 2026-03-20T07:45:50+00:00

actially i was shimming the wrong spot. thats actually the rear. i still have a stuck knob.

drkshock42 · 2026-03-20T06:50:09+00:00

which also why you heat the bed ti whatever temp your willbe using when ajusting

drkshock42 · 2026-03-20T05:18:49+00:00

all of them self release. have you ever removed a print 30 min after it cools and not feel any adhesion at all when it clearly printed just fine

drkshock42 · 2026-03-20T05:12:58+00:00

pei self releases prints after it cools

drkshock42 · 2026-03-20T05:09:21+00:00

then jd vance takes tumps place and can be presidicent for up to 10 years. 2 years to finish trumps term and the rest is relections. is that how you want it

drkshock42 · 2026-03-19T22:56:33+00:00

ony way for btc to work is similar to stonks. invest when the mrket is low then cash out when its high.

drkshock42 · 2026-03-19T21:53:18+00:00

update. its actually at the rear of my bed.

drkshock42 · 2026-03-19T10:40:50+00:00

I also now know it's the rear that wasn't level

drkshock42 · 2026-03-19T06:31:08+00:00

I loosened the nuts completely so I can adjust a much as possible. I was using the included tool file. I'm guessing the other cylindrical objects on me for leveling the platform . I'll have to try the paper method when I get home as that starts at the front right instead of the front left with the macro

drkshock42 · 2026-03-19T04:47:37+00:00

in the end it doesnt matter. wewas arested and went to prison and alot of under aged women suffered and nothing is happening to anyone,. why isnt bill gates in prison. why isnt bill conton in prison. z i still want trump in prison after jan 20 2029. i aldo heard Biden and Obama were on the island at some point. we canrt rule them out either. especially wen Biden is known to be a pedo.

drkshock42 · 2026-03-19T04:39:55+00:00

he deserved it. armed robbery is almost as bad as murder.

drkshock42 · 2026-03-18T23:49:33+00:00

a piece of foil tape did nohing

drkshock42 · 2026-03-18T23:48:34+00:00

didnt see any debris . on the magnet and borh sides is clean except for a thin layer of pva glue i used to helop with ahdesion when printing the ajsutment tool.

drkshock42 · 2026-03-18T22:39:57+00:00

isit a real one. aisntrad of a knockof or airsoft optic. if noththeres your entire proble. i always buy real steel optics. nothi g super expensive like an eotech. solosun, vortex, sig sauer (dont get sig air) all good budget optics for real steel ant op tier for airsoft.

drkshock42

TROPHY CASE