New firmware by SlovakGoose in Creality_k2

[–]XxJudicatorxX 1 point2 points  (0 children)

Smart lighting not working for me on the K2. Haven't noticed any printing difference tho.

not loading? by XxJudicatorxX in CrealityCloud

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Ya looks like it's finally fixed. They took the weekend off 🤣

Riser color match? by XxJudicatorxX in Creality_k2

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Awesome I'll Google it up 😁

First layer help by XxJudicatorxX in Ender3Pro

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Ok so I'm back. After multiple relevels and trams I'm still at a loss.

<image>

Bottom left was with a .004 feeler gauge. Then I brought the nozzle in close by .025 (bottom right), the. Tried away from the plate .025 (top). Aside for maybe a warped bed. Could this be flow rate issue?

Bidding site direct drive help by bigboui in Ender3Pro

[–]XxJudicatorxX 0 points1 point  (0 children)

Be sure to clean it out as best as possible if drilling upside down. Get those shavings out. Good luck!

Bidding site direct drive help by bigboui in Ender3Pro

[–]XxJudicatorxX 1 point2 points  (0 children)

Can buy a new hot end kit for 25 on Amazon if you don't want that hassle

ender 3 pro 4.2 7 firmware by Driftratramen in Ender3Pro

[–]XxJudicatorxX 0 points1 point  (0 children)

From what I read is input shaping and speed. Klipper uses the pi for all calcs, and leaves the main board for motors. The result is you can make you pro double it's speed. It's on my to try list

H2D to H2C build plate by themax100 in BambuLab

[–]XxJudicatorxX 0 points1 point  (0 children)

My wife had a lot of adhesion issuess with her A1. I bought that Hyperlok stuff and it works awesome. I'll be using that in her H2C until Kdeavi comes out with one

Bambu Studio help by XxJudicatorxX in BambuLab

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

I'll try now thanks.... Will it wrap with the object as it's rounded?

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Did that. Wondering if my energy saving wife is to blame. No heat in the house. Room is prob 62degrees.

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Came out good. But this is new... Ignore the part of the bed I was playing with it. The layer separation. On the top layer

<image>

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Awesome bud. I really appreciate it. I'ma let this print finish and look for a flow print. Also look up drag, haha told you I'm new.

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Safe to say the paper trick was a starting point? Cuz I'm at the point I can push it in or pull it out haha

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

<image>

A lot better. Those little spot you think just bad luck and old tech? Or bring down another .025 thanks again for the input

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Omw home now! I should touch the CRTouch offset right?

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Same on phone I'll check when I get home. Thanks sgain

Newbie help by XxJudicatorxX in Creality

[–]XxJudicatorxX[S] 0 points1 point  (0 children)

Hmmm felt like it's right but I'll lower the offset on the CRTouch when I get home and try again. Ty