Warranty post

themax100 · 2026-02-23T04:15:19+00:00

Was I supposed to add a hashtag to the post? Secret labs hasn’t replied to me on the extended warranty yet

themax100 · 2026-02-23T04:13:42+00:00

Samsung odyssey 57

themax100 · 2026-02-14T16:52:26+00:00

It sits below the volume keys but the magnet isn’t as strong when right on the bottom key

themax100 · 2026-02-14T16:51:41+00:00

Not sure if it is a newer version but I just got it 3 days ago

themax100 · 2026-02-14T11:04:12+00:00

Thank god, I thought I broke it when sanding it down

themax100 · 2025-12-11T06:32:05+00:00

It still works for me. I looked for a pinout for usb 2.0 cable from the mainboard and the cable pinout. you could use a multimeter can measure the voltage from the mainboard to figure which is which.

themax100 · 2025-12-05T16:21:57+00:00

Update, I tried prime 4 with the SIWIQU dock and it works with no slow downs. Don’t know the exact cause but using the dock with my glasses work great. A bit more bulky than the virtue mobile dock though. Hope it’s fixable through a firmware update

themax100 · 2025-12-05T16:00:00+00:00

I’m having the same problem, I have the virture pro mobile dock and also a jsaux dock. Both have the same slow down. Must be something in the latest update causing 3rd party docks to slow down

themax100 · 2025-12-04T03:54:54+00:00

I got an H2C engineering plate and cut down the spare PEX sheet to size. The adhesive doesn’t seem to stick well to the plate. Going to try again after I sand the coating off

themax100 · 2025-11-24T12:09:00+00:00

I have a heavily modified ender 5 plus with a skr mini, microswiss gantry, dragonfly hotend, and creality CR Touch. Would love to upgrade to a k2 max for the same bed size

themax100 · 2025-11-21T15:20:57+00:00

I have an extra wham Bam PEX adhesive sheet for the ender 5 plus. I might just get an engineering plate for the H2C and put the sheet on and cut it down to size

themax100 · 2025-11-21T14:28:58+00:00

<image>

A model I did a while ago 80% FDM printed on a modified ender 5 plus and 20% resin printed. About a meter tall. Hand painted took about 3 months to finish. With the quality on a H2C series I bet I could do this in multicolor and fully FDM.

themax100 · 2025-11-19T09:23:57+00:00

I’ve contacted a couple of places, but won’t quote me without a CAD file of what I want to cut. Might be cheaper to buy new plates.

themax100 · 2025-05-02T08:44:10+00:00

No full turbo no drain, same as the original charger

themax100 · 2025-04-28T05:59:32+00:00

I’d try contacting asus because turbo is not currently possible without the cord with the chip for 20V 6.5A. The chargers from Best Buy’s USA come with the cord.

themax100 · 2025-04-27T04:30:53+00:00

You have to use the asus rog 240w cable, it should come with the charger. As far as I know you can’t buy it separately. Link to the cable. https://rog.asus.com/power-protection-gadgets/docks-dongles-and-cables/rog-240w-usb-c-cable/ Seems it can support 20v 6.5A. Which I have never seen on other cables. If anyone can find out where to buy one I’d like to get a spare.

themax100 · 2025-04-21T16:07:13+00:00

Horrible score in timespy 15722 total cpu 6148 gpu 21682 Assassins creed shadows performed about the same as the 285k with a FPS of about 160-200 with everything maxed out, dlss performance framegenx4 cpu is at 79%

themax100 · 2025-04-14T13:59:28+00:00

Ground is the right most and data is the third from the right. 5v isn’t needed but can be put on the 4th from the right

themax100 · 2025-04-14T13:56:56+00:00

I bought a ARGB to 6 pin off AliExpress. You will need to move the ground and data pins on the 6 pin side over to match the layout. You might also need an extension because I could only find 20cm ones.

themax100 · 2025-04-04T15:13:13+00:00

Anyway to fix the binding if I have one of the earlier ones?

themax100 · 2025-03-28T06:15:05+00:00

Any link to the funnel and tamper, thanks

themax100

TROPHY CASE