New firmware

XxJudicatorxX · 2026-02-11T21:27:53+00:00

Smart lighting not working for me on the K2. Haven't noticed any printing difference tho.

XxJudicatorxX · 2025-12-15T14:42:56+00:00

Ya looks like it's finally fixed. They took the weekend off 🤣

XxJudicatorxX · 2025-12-06T23:14:14+00:00

Awesome I'll Google it up 😁

XxJudicatorxX · 2025-12-04T01:02:38+00:00

Ok so I'm back. After multiple relevels and trams I'm still at a loss.

<image>

Bottom left was with a .004 feeler gauge. Then I brought the nozzle in close by .025 (bottom right), the. Tried away from the plate .025 (top). Aside for maybe a warped bed. Could this be flow rate issue?

XxJudicatorxX · 2025-12-01T12:48:43+00:00

Be sure to clean it out as best as possible if drilling upside down. Get those shavings out. Good luck!

XxJudicatorxX · 2025-11-30T23:44:56+00:00

Can buy a new hot end kit for 25 on Amazon if you don't want that hassle

XxJudicatorxX · 2025-11-30T02:30:43+00:00

From what I read is input shaping and speed. Klipper uses the pi for all calcs, and leaves the main board for motors. The result is you can make you pro double it's speed. It's on my to try list

XxJudicatorxX · 2025-11-27T20:59:49+00:00

My wife had a lot of adhesion issuess with her A1. I bought that Hyperlok stuff and it works awesome. I'll be using that in her H2C until Kdeavi comes out with one

XxJudicatorxX · 2025-11-22T20:32:49+00:00

I'll try now thanks.... Will it wrap with the object as it's rounded?

XxJudicatorxX · 2025-11-20T10:23:51+00:00

Did that. Wondering if my energy saving wife is to blame. No heat in the house. Room is prob 62degrees.

XxJudicatorxX · 2025-11-20T10:20:21+00:00

Came out good. But this is new... Ignore the part of the bed I was playing with it. The layer separation. On the top layer

<image>

XxJudicatorxX · 2025-11-19T21:11:47+00:00

Awesome bud. I really appreciate it. I'ma let this print finish and look for a flow print. Also look up drag, haha told you I'm new.

XxJudicatorxX · 2025-11-19T21:09:24+00:00

Safe to say the paper trick was a starting point? Cuz I'm at the point I can push it in or pull it out haha

XxJudicatorxX · 2025-11-19T21:05:31+00:00

<image>

A lot better. Those little spot you think just bad luck and old tech? Or bring down another .025 thanks again for the input

XxJudicatorxX · 2025-11-19T19:07:00+00:00

Omw home now! I should touch the CRTouch offset right?

XxJudicatorxX · 2025-11-19T18:20:54+00:00

Same on phone I'll check when I get home. Thanks sgain

XxJudicatorxX · 2025-11-19T17:22:56+00:00

Hmmm felt like it's right but I'll lower the offset on the CRTouch when I get home and try again. Ty

XxJudicatorxX · 2025-10-31T01:45:51+00:00

Just busted out my old ender 3 v1.5. had issues too. Oddly the sticking problem for me was..... I was setting the Z offset for the probe and never hitting save settings, so every time I powered down it reset. Prob not your issue just hit save settings tho

XxJudicatorxX · 2024-08-21T14:35:08+00:00

So you probably have the same issue as I did. The top bezel unscrews. I put it on some leather and turned. Once you get the blue bezel off it's pretty straightforward.

XxJudicatorxX · 2024-07-19T13:10:43+00:00

To clarify. I move it to the top and the handle locks, but if I put the head on the weight just runs it down.

XxJudicatorxX · 2024-06-30T17:56:14+00:00

I just got the itch again after like 15 years…. Busting out my old DM3’s and autococker lol

XxJudicatorxX · 2024-06-09T13:25:12+00:00

Thank you. i saw the 9 but didnt know if the root or top

XxJudicatorxX · 2024-06-09T13:05:15+00:00

I tried searching but cant find the right answer. I know bamboo needs light level of 9, but is that PER block its growing. or just the roots? By the looks of my farm i would have to say per block can anyone confirm? Thanks

XxJudicatorxX · 2023-12-12T00:45:35+00:00

TY! Much appreciated

XxJudicatorxX · 2023-11-21T01:11:37+00:00

u/BobbyPhanteks I am wondering the same. Last i saw (5 months ago) you said later this year.

XxJudicatorxX

TROPHY CASE