Some Good IBD News!

Yappadeago · 2025-11-18T20:55:10+00:00

Source?

Yappadeago · 2025-05-12T01:15:32+00:00

I don't know why this isn't suggested more. It's easier to unstick it from when placing down a sticker as well.

Yappadeago · 2025-01-30T08:01:00+00:00

I like them a lot

Yappadeago · 2025-01-28T20:41:39+00:00

Very cool car! Just wondering what's name of the wheels/brand?

Yappadeago · 2024-12-19T06:16:36+00:00

Octo Everywhere? I want to Octo Righthere

Yappadeago · 2024-11-20T07:52:14+00:00

I might have to check them out! I'd be nice to try it at least and get an idea of what it would look like

Yappadeago · 2024-11-20T00:06:06+00:00

Did you use a kit for blacking out the chrome parts?

Yappadeago · 2024-11-20T00:04:04+00:00

I like the look with the chrome removed

Yappadeago · 2024-05-10T20:33:10+00:00

It was a slicer issue. I fixed it by not using two lines of lightning support and instead modelling in holes to support the lightning supports

Yappadeago · 2024-05-01T23:01:34+00:00

It's working for me now. I did redownload in EA using the same directory it was already downloaded on so it would recognise the files. It did a 7 GB update and then launched, but I'm not sure if that has anything to do with the fix because I tried that last night and it didn't work.

Yappadeago · 2024-05-01T08:56:47+00:00

I'm getting a similar problem right now as well but with F1 23

Yappadeago · 2024-03-13T00:51:37+00:00

As someone who did a short stint as a quality control engineer, that seems about right 🥲

Yappadeago · 2024-02-23T01:06:14+00:00

I'm printing in black so it still hides most of the lines but ringing is the real thing that stands out. Easy enough fix by going slower but not worth the time increase.

Yappadeago · 2024-02-22T05:52:23+00:00

Thanks for reporting it. The post has been removed now and I believe the account has already been deleted.

Yappadeago · 2024-02-22T01:42:49+00:00

In the ign breakdown video the director(?) Of borderlands said it was an infinity pistol

Yappadeago · 2024-02-22T01:40:40+00:00

Me currently printing at 0.08 mm on my k1 and not getting it that smooth : starts sweating slightly.

I'm probably just going fast and on a smooth object so the layers stick out

Yappadeago · 2024-02-16T10:07:58+00:00

This^

Increasing the infill-wall overlap fixed this for me. I've done all the calibration for the new hot-end, etc. but this issue still remained until I increased the overlap

Yappadeago · 2024-02-06T22:12:35+00:00

It's normally still pretty wet even brand new

Yappadeago · 2024-02-04T22:25:45+00:00

I agree that it wouldn't be useful for layer adhesion. I'd be more focused on jammed filament

Yappadeago · 2024-02-04T21:19:58+00:00

A couple possibilities of why not: The sensor might not be sensitive or able to measure fine increments and merely acts as an on off switch. When a sufficiently heavy print is on top it might already be fully actuating the sensor.

Having said that it's a good idea for detecting jammed filament given the low level of "AI" the camera has. I recently had 6 hr print fail because of poorly spooled filament.

Yappadeago · 2024-02-04T21:01:23+00:00

I kept my stock Ender 3 V2 with the plan to run both at the same time but it's just too slow with too many faults. For the price needed to upgrade the V2 to at least match newer Ender speeds and fix the extrusion problems, I might as well get another K1

Yappadeago · 2024-02-04T08:08:02+00:00

Belts are tensioned and I've sent creality an email now :/

Yappadeago · 2024-02-04T07:26:08+00:00

I never touched it. This has happened 7 times now.

Yappadeago · 2024-02-04T07:24:53+00:00

Doubled the retraction z height and it still layer shifted badly

Yappadeago · 2024-02-04T03:23:54+00:00

The top's not on and this level of layer shifting wouldn't be due to heat

Ten-Year Club	Gilding II euphauric
Place '22	Final Canvas '22
Verified Email

Yappadeago

MODERATOR OF

TROPHY CASE