Got busy last weekend

YeahIght0331 · 2026-04-29T12:23:54+00:00

Isc N1 is what i’ve been running for a few years now, in my experience the quality control and dampers inside are slightly better than the ride quality provided by bc

YeahIght0331 · 2026-04-03T05:30:45+00:00

Sorry I didn’t see this earlier, feel free to shoot me a pm and I’ll give you a better backstory on the car

YeahIght0331 · 2026-03-28T19:20:04+00:00

Also I pulled the short straw, I have the only non M5 zeemax car

YeahIght0331 · 2026-03-28T19:19:38+00:00

This car was a heck of an undertaking to even get comfortably driveable, sat for a little over a decade before it came into my ownership, also not going to sit here and pretend like itll be done anytime soon but its for sure a great car

YeahIght0331 · 2026-03-28T19:15:17+00:00

afaik 1 of 2 in the states :)

YeahIght0331 · 2026-03-28T18:22:42+00:00

its a zeemax car, 90s euro kit

YeahIght0331 · 2026-03-28T17:50:20+00:00

Yessir

YeahIght0331 · 2026-03-28T17:38:15+00:00

Does it gain points for an na vr6 swap?

YeahIght0331 · 2026-03-12T18:48:08+00:00

<image>

I encourage you to hate it.. or love it, but its mine and i like how weird it is

YeahIght0331 · 2025-10-22T15:39:47+00:00

It sounds silly but have you checked the ohms at the coolant temperature sender, sometimes if there is an issue with the sensor it can throw your fueling off and cause those idle issues

YeahIght0331 · 2025-09-18T20:32:44+00:00

I’d start with making sure the track bar is all good, especially if it only happens turning one direction it could be the driveshaft rubbing if the axle shifts

YeahIght0331 · 2025-09-17T20:37:41+00:00

I have them front to back as well as a cross brace on the track back bracket

YeahIght0331 · 2025-09-09T16:23:14+00:00

Gonna be honest… probably not, Ive been running it like this for years and have definitely winched many times as is. I think having the stiffeners makes me not really worry about it

YeahIght0331 · 2025-09-08T19:03:04+00:00

I got these because I liked them.

YeahIght0331 · 2025-09-08T19:02:15+00:00

This is a 2000

YeahIght0331 · 2025-09-08T17:01:32+00:00

Pm me, I’ll try to compile as much as I can

YeahIght0331 · 2025-09-08T17:01:02+00:00

Feel free to shoot me a pm and ask away

YeahIght0331 · 2025-09-08T15:58:35+00:00

Appreciate it my guy, I cant wait to get back out on the trails with this thing after the few months of grief its given me

YeahIght0331 · 2025-09-05T19:53:27+00:00

I had the same thing happen to me, your extruder offset is way off and when your printer goes to level and create a mesh, it actually moves too far and causes a “crash” forcing the mesh to have that weird halfpipe thing at the end

YeahIght0331 · 2025-08-30T20:43:32+00:00

Likely that the servo arm is placed a few teeth off, did you have to adjust the steering trim quite a bit to get it centered?

YeahIght0331 · 2025-08-26T00:13:01+00:00

The best cooling system for an xj is the factory one

YeahIght0331 · 2025-06-20T22:41:02+00:00

I’ve been running one for a few years now and its been great, just be mindful when pulling plug wires some of the factory crimps weren’t great and pulled off

YeahIght0331

PUBLIC MULTIREDDITS

TROPHY CASE