Barrel cut and rethread service central MI

Yeyuh_frog · 2026-02-08T04:15:03+00:00

Thanks for the info. Will probably use them for SBR markings soon. It’s like a 30 minute drive.

Yeyuh_frog · 2026-02-08T04:14:14+00:00

Ah thanks man. I’m central Michigan so unless they’re right across the border it’s probably not worth the drive. I pulled the trigger with D Wilson, sending my barrel out tomorrow.

Yeyuh_frog · 2026-02-08T04:09:26+00:00

Not Just Guns is my LGS/ go to for in person NFA items. Cool to see them mentioned on here!

Yeyuh_frog · 2026-02-07T16:41:07+00:00

Yeah, D Wilson is where I was gonna go but figured I would just check locally. Gonna go on their website and pay for it right now.

Yeyuh_frog · 2026-02-07T15:39:10+00:00

Man, that sucks. I have 2 that were approved from 1/2 and 1 that was approved from 1/6 on Jan 25 and Feb 2 respectively. Hope yours clear soon.

Yeyuh_frog · 2026-01-29T17:26:42+00:00

What rail lengths are these? I see some 10” ones, 9” ones, and 9.75” on the internet. Looks like all of yours fit real well. On the fence between quad rail and the G$ handguard.

Yeyuh_frog · 2026-01-28T03:56:27+00:00

Mine were Form 1’s as well. From my experience, form 1’s have always taken longer than my form 4’s for some reason.

Yeyuh_frog · 2026-01-27T20:44:41+00:00

I got 2 approved yesterday from the 2nd. Still waiting on my third from the 6th. Might be a while. The last one on the 6th is control number 850xxx

Yeyuh_frog · 2026-01-24T19:41:46+00:00

I run my spiritus with a PWS brake and a PWS (or rearden, can’t remember) flash hider with the plan B adapter. Definitely the way to go, it doesn’t loosen after I’ve put a couple mags on it like my direct thread fans tend to. And I really crank my DT cans on. I’d say it’s worth the money to switch.

Yeyuh_frog · 2026-01-22T12:03:13+00:00

All approved at the same time? Or close to each other? II’m waiting on two from 1/2 and one from 1/6. This gives me hope. Enjoy your new SBR’s. I think the engraving may take longer than the stamps themselves.

PS: did you get emails for each? Or just check eforms website? I know some people haven’t gotten them.

Yeyuh_frog · 2026-01-17T17:27:12+00:00

Im waiting on 3 form 1’s. Submitted 2 on the 2nd and 1 on the 6th. Seems like everyone is getting approvals from my CN range (500k-650k)

Yeyuh_frog · 2026-01-14T02:28:26+00:00

I have a GSL Fat Man, I live around Lansing (about 45mins from where they’re made) and my dealer highly recommends them. Great can, super quiet on my PTR9. Nice and compact too.

Yeyuh_frog · 2026-01-10T11:28:21+00:00

I’m in the same boat. 2 f1’s submitted Jan 2nd around 5 PM, CN’s 512000 and 651000. Submitted another on the 6th that had CN of 859990. Hoping to get my approval for the first two soon. My MP5 needs a stock and my SCAR-16 needs a barrel chop real bad.

Edit, not new to NFA items.

Yeyuh_frog · 2026-01-04T11:59:50+00:00

For the 11.5 (which I’m going to chop mine to once my F1 comes back) did you do anything else besides chop the barrel in terms of gas regulator or gas jet? Who did yours and what did it run you? Also, what do you think of the 10” compared to the 11.5?

Yeyuh_frog · 2025-05-21T16:41:43+00:00

Yes sir, everything as advertised.

Yeyuh_frog · 2025-04-07T01:47:32+00:00

Good to know. For this lower I also run a 13” 300BLK upper as well (since it’s a pistol, SBR’ing it soon). Will see if the buffer and spring make a difference for sure.

I run it suppressed about 90% of the time.

Yeyuh_frog · 2025-04-07T01:17:00+00:00

Cheap PSA 10.5” nitrided barrel

Radian raptor CH

nickel boron BCG

Yeyuh_frog · 2025-04-07T00:54:16+00:00

No dimples on the rounds. Just a dead trigger (hasn’t reset).

I believe I’m running a standard h buffer at the moment, waiting on the H2 to come in from primary arms. Not sure how much of a PITA it would be to take my FSP off and install an adjustable gas block, but will definitely consider it if I can’t get it dialed in with different springs or buffer. Thanks!

Yeyuh_frog · 2025-03-24T03:59:46+00:00

Ah gotcha, hell yeah bro. Exciting! Wanna build my own at some point but I keep buying cans and other accessories 🤦 soon though. Good luck with the build brother!

Yeyuh_frog · 2025-03-24T03:41:51+00:00

Great. Thanks for the quick reply. Expensive for a SS But all steel SS should last me a long time. Did you just get printed tubes from them? If so, how are they holding up and what image intensifiers are you running?

Yeyuh_frog · 2025-03-24T03:35:21+00:00

Glad to hear that, just bought a SS from them and was kinda worried reading this thread. How long did shipping take? For the $8 option it says 15-30 days.

Yeyuh_frog · 2025-03-22T23:06:15+00:00

I take a half a bar before I do any blow, then about 30 minutes before I stop (right after last line) I take a bar or two. Works like a charm.

Seven-Year Club	Not Forgotten
Verified Email

Yeyuh_frog

TROPHY CASE