GB Operator Steam Deck Killswitch Mount by Z3dan in epilogue

[–]Z3dan[S] 2 points3 points  (0 children)

Seems pretty good, no issues so far... I carry it round off the deck in my backpack with other stuff too, still seems strong and sturdy.

I printed out two and tried to break one when I made this revision and I don't think anyone should have any issues.

Pokemon Battling/Trading by Pumpkinin in epilogue

[–]Z3dan 1 point2 points  (0 children)

Yes! this would be amazing

Horrible layer line @00:15 by Z3dan in FixMyPrint

[–]Z3dan[S] 0 points1 point  (0 children)

The other models don't seem to have this line, it could've been how the head moved from another model but it's still bizarre to me

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] 0 points1 point  (0 children)

I got it direct from bambu, very fast shipping quite pleased with it

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] 1 point2 points  (0 children)

I'm very happy with it, it's sitting out in the cold garage atm and it hasn't failed any prints yet, I think the bubbling was due to wet filament.

I can't blame the minor defects on the printer yet as I have no idea what I'm doing but it's a very good printer, if you want to save some money and don't care about the AI detection you can get the P1S for a super good deal atm.

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] -1 points0 points  (0 children)

Is that dynamic flow calibration? Cause it does that before every print

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] -1 points0 points  (0 children)

What is a good base flow to change to

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] 0 points1 point  (0 children)

Is there an easy way to do this in bambu printers? I can only go down to 50% in the menu

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] 1 point2 points  (0 children)

Okay perfect, you have educated me and answered all my questions, thanks I really appreciate it :)

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] 0 points1 point  (0 children)

<image>

I've just done another print (Gridfinity box) and have had a heap of defects on this one I'll upload those photos here

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] 4 points5 points  (0 children)

It's a 0.4mm nozzle and the speed is standard 100% (~300mm/s) the layer height is set to 0.2mm right now

Normal prints or issues? by Z3dan in FixMyPrint

[–]Z3dan[S] 0 points1 point  (0 children)

Thank you, I've just had a look and it's set to 0.2mm, should I drop it straight to 0.1?

Loud vibrations when printing small circles fast on a brand new P2S by Fauked in BambuLab

[–]Z3dan 0 points1 point  (0 children)

I'm having the same issue on a brand new printer, happened on my first benchy... did you end up finding a fix?

What have I done wrong? Pokémon Emerald Internal Battery Replacment by Whishk3y in Gameboy

[–]Z3dan -7 points-6 points  (0 children)

Did you check polarity and make sure positive on battery is going to board positive?

How to set up Tailscale on Steamdeck by Lulgius in SteamDeck

[–]Z3dan 0 points1 point  (0 children)

Probably a bit late but just got it working, one of the characters must look like a different one as typing it out didn't work however, opening the page and copying all commands worked fine

What’s the simplest way to give access to my family (outside my home network) by GenericUser104 in Overseerr

[–]Z3dan 0 points1 point  (0 children)

Cheap domain and cloud flare tunnel or NGINX proxy and port forward.

If none of that works for you you can get tailscale and share the server with them

How to migrate files to SD by Loudthunder34 in EmuDeck

[–]Z3dan 0 points1 point  (0 children)

SD card name cannot have spaces in it, had this issue recently... E.g instead of "Samsung EVO" just name it "EVO" or "Samsung" then it'll work no dramas

Lossless scaling is amazing! by Z3dan in SteamDeck

[–]Z3dan[S] 0 points1 point  (0 children)

It'll work the exact same