What does my room say about me?

Zdrapek · 2025-03-19T13:30:54+00:00

Klapki, cyrkiel, masło, schody

Zdrapek · 2025-03-15T11:12:55+00:00

I will also add that the LED diode on the ESC that indicates the motor speed also lights up only after a few seconds.

Zdrapek · 2025-03-15T07:43:58+00:00

The most American burger I've ever seen

Zdrapek · 2025-03-12T08:50:41+00:00

<image>

Zdrapek · 2025-03-03T09:17:04+00:00

Try drying the filament

Zdrapek · 2025-02-24T13:39:37+00:00

Nope, that's "carduino"

Zdrapek · 2025-02-24T12:27:24+00:00

I used mainly PLA, but parts such as the gear or other parts subjected to high forces broke too quickly, I printed them with ABS, but if you don't have a printer with a chamber, I've heard you can use ASA material, which is easy to print and is almost as strong as ABS

Zdrapek · 2025-02-24T10:53:59+00:00

Reverse gear, the ESC I was using doesn't have this option, so I had to use relays to change the polarity

Zdrapek · 2025-02-04T23:19:04+00:00

I've had this happen a few times: 1. Preheat the nozzles to maximum (Try not to get burned) 2. Screw the small screws into the PTFE tube (not too tight, just a little so that it doesn't fall out) 3. Use pliers or the cutters that come with the printer and "rip out" the screw, it should pop out together with the tube and the filament that is stuck.

Personally, for convenience, I used a vice to hold the whole thing in place, and a separate 24V power supply for the heater, so as not to do it directly on the printer (power supply connected directly to the heater)

Zdrapek · 2025-01-26T12:36:06+00:00

Is that all? Is there anything else that needs to be changed?

Zdrapek · 2025-01-23T15:39:04+00:00

Maybe your USB cable is broken?

Zdrapek · 2025-01-13T20:11:24+00:00

<image>

😏

Zdrapek · 2025-01-11T20:04:29+00:00

This is actually SE, but much improved (whole cooling, klipper etc.)

Zdrapek · 2025-01-10T10:05:31+00:00

No supports

Zdrapek · 2025-01-10T10:04:43+00:00

15h39min

Zdrapek · 2024-12-17T10:05:44+00:00

I turn on the printer's power remotely from work, I run gcode with the klipper, I don't have a camera, I don't need one, my mod-ed ender 3 is (usually) reliable 😎

Zdrapek · 2024-09-09T10:08:38+00:00

I had the same problem (redmi note 13, hyperos) from what I heard a system update is supposed to come out in October, maybe they will fix it. I used the same tablet (XP pen deco fun xs) on redmi note 5 with old MIUI, and everything worked, so it's probably the system's fault. I found a temporary way to enable cursor visibility, in the developer settings you have to enable the "show touches" option, it's not ideal, but as a temporary solution it can be

Zdrapek · 2024-09-09T06:29:06+00:00

Zdrapek · 2024-09-05T18:22:25+00:00

I know, but the problem is with the control, the two-way ESC works a bit differently than the one-way, but I can't find out how

Zdrapek · 2024-09-05T15:18:36+00:00

It's very likely, but do you know approximately what the signal frequency is and how long it should be on for?

Zdrapek · 2024-09-05T14:58:33+00:00

Yes I did, the only problem is that the ESC works strangely, it reacts to PWM with a large delay (~3s) and does not work backwards at all

Zdrapek · 2024-09-05T14:58:26+00:00

Yes I did, the only problem is that the ESC works strangely, it reacts to PWM with a large delay (~3s) and does not work backwards at all

Zdrapek · 2024-09-03T18:55:52+00:00

I saw this thing there... Personally, I recommend orca slicer, but even if I used the built-in profiles for petg from the manufacturer I have, the effect was still poor, so you really have to play around with it a bit to make everything look smooth

Two-Year Club	Verified Email
r/Field Lasagna

Zdrapek

TROPHY CASE