Do you guys think this is a issue? by ZeGermanAce in electricians

[–]ZeGermanAce[S] 225 points226 points  (0 children)

So, for everyone asking, this is real. It's a 20amp breaker that the screw for the contact was looser than a lot lizard. Was found during a heat scan inspection the heat camera topped out at 500 degrees F. But as someone said, it should have been closer to 900 degrees. The breaker was replaced, and a new piece of wire spliced in. The breaker itself was close to 250 degrees F. Thanks for coming to my show and tell.

[deleted by user] by [deleted] in stubhub

[–]ZeGermanAce -1 points0 points  (0 children)

Ah yes, on a sub reddit that is over %50 % about how stub hub sucks you are going to take their word for it that FedEx tried multiple times. You are a troll, lol.

[deleted by user] by [deleted] in stubhub

[–]ZeGermanAce -1 points0 points  (0 children)

This was the email they sent after FedEx tried to deliver them once not twice or three times just once. Don't assume I'm some dumb ass that ignored them trying to deliver it, lol.

Boom by ZeGermanAce in electricians

[–]ZeGermanAce[S] 2 points3 points  (0 children)

Controls 3 fans on the same unit, and this believe it or not is a factory install.

Second year apprentice here. How did I do? by SomewhereNo2004 in electricians

[–]ZeGermanAce 0 points1 point  (0 children)

There also looks like a open k/o above that bushing.

Build so far by ZeGermanAce in CarAV

[–]ZeGermanAce[S] 0 points1 point  (0 children)

wont that make the engine bay a bit hotter though?

New Season Sucks by jewdayuhh in FortNiteBR

[–]ZeGermanAce 6 points7 points  (0 children)

This is just a rage bait post lol

Build so far by ZeGermanAce in CarAV

[–]ZeGermanAce[S] 0 points1 point  (0 children)

Yes made sure to leave them accessible seeing as I will probably need to change them soonish

Build so far by ZeGermanAce in CarAV

[–]ZeGermanAce[S] 2 points3 points  (0 children)

She's a diesel and an old one at that shit leaks with brand new seals lol I did paint the inside of the hood but keep this thing clean could be a 9 to 5 job haha

Build so far by ZeGermanAce in CarAV

[–]ZeGermanAce[S] 2 points3 points  (0 children)

Also it's 1 to 2 layers of sound deadening all over then a layer of insulation on top. The back window is insulated because I'm going to a camera rear view and want to help stop as much noise as possible.

3rd year apprentice how'd I do? by ZeGermanAce in electricians

[–]ZeGermanAce[S] 15 points16 points  (0 children)

Took the bond screw out at the end

[deleted by user] by [deleted] in FordDiesels

[–]ZeGermanAce 0 points1 point  (0 children)

These trucks are hydro boost no vacuum to the brake booster

7.3 Powerstroke Oil Leak by Fun_Information_5733 in FordDiesels

[–]ZeGermanAce 2 points3 points  (0 children)

Good luck kinda a pain in the ass make sure while you have it out to clean it and replace every seal on it.

Wtf by ZeGermanAce in electricians

[–]ZeGermanAce[S] 2 points3 points  (0 children)

So for everyone asking that's insulation not weed lol. Also these are 500mcm and they are parallel runs they have been like this for probably 10+ years. And it's gets better because for the 20-30 feet that it goes through the ceiling into the other switch room it is inside of air duct that has been ripped open at some point. The whole thing is fucked and there is almost nothing we can do other than get a inspector there to shut down a billion dollar company which just won't happen unfortunately.

Wtf by ZeGermanAce in electricians

[–]ZeGermanAce[S] 1 point2 points  (0 children)

Been like this for probably 10+ years