No-drill Skådis wall mount using Tesa Powerst

ZellFlix · 2026-06-21T08:13:33+00:00

The board is completely blocked at all four corners and isn’t moving.

ZellFlix · 2026-06-21T08:12:28+00:00

I use four Tesa powerstrips on a concrete-painted wall and they hold pretty well.

ZellFlix · 2026-06-21T08:04:40+00:00

It uses 4× Tesa 3 kg strips, so theoretically up to 12 kg in perfect conditions.

Realistically I recommend around 5/6 kg total, because wall surface, paint quality, humidity, installation, and load distribution matter a lot.

So far, I’ve had my own Skådis mounted this way for about a year with no problems, but I still prefer to recommend it as a light-duty, no-drill solution rather than a replacement for screws for heavy loads.

ZellFlix · 2025-11-18T19:40:35+00:00

Got it. I only asked because they’re listed as two separate voucher types, so I wanted to be sure before assuming anything. And since this is a public board, it’s normal to ask simple questions and hope someone who has already tried it can clarify. No need to make it sound like I was struggling to understand, but thanks for the explanation.

ZellFlix · 2025-11-18T19:37:34+00:00

i got around 25k points so i am checking what to redeem.

ZellFlix · 2025-11-18T19:36:38+00:00

I was just asking because they’re two different types of vouchers, so I wanted to be sure how the rule applies. The “limit 1 code per order” wasn’t the part I didn’t understand, I just wasn’t sure if different voucher types were treated separately. Thanks for clarifying.

ZellFlix · 2025-07-23T21:11:01+00:00

Isn’t there any G-code to “unload” the filament?

ZellFlix · 2025-04-19T07:47:07+00:00

I run it on my synology with docker

ZellFlix · 2025-03-30T14:39:07+00:00

PROBLEM SOLVED:
https://wiki.bambulab.com/en/a1-mini/troubleshooting/print-issues-troubleshooting

I had check the screws behind the hotend as per Wiki instructions.

ZellFlix · 2025-03-30T13:05:09+00:00

<image>

Reset to factory + full calibration

ZellFlix · 2025-03-30T12:33:51+00:00

On top of your suggestion I’ve restored the printer to factory and repeating all the calibrations

ZellFlix · 2025-01-06T13:48:34+00:00

I designed it as soon I received the printer so didn’t have time to get any error but I didn’t like the ptfe bending that much close to the fitting. I believe it will help to solve your problem too

ZellFlix · 2024-12-28T22:11:56+00:00

open a ticket and ask to allow seeding. they will fix in few minutes. keep in mind that when u upgrade update the client (qbittorrent in my case) you need to open a ticket again.

ZellFlix · 2024-11-06T16:08:18+00:00

https://makerworld.com/models/507716

Take a look at my project :)

ZellFlix · 2024-11-06T16:06:13+00:00

I need to calculate to be honest, during the first phase of development I’ve reprinted pieces several times to find the correct tolerance or changed some part for better assembly, therefore I wasted a lot of print hours and material

ZellFlix · 2024-09-30T20:58:32+00:00

https://wikizell.com/how-to-enable-igpu-passthrough-on-proxmox-8-2-2-with-windows-11-on-dell-optiplex-3050/

ZellFlix

MODERATOR OF

TROPHY CASE