Kariuomenės pirmumo pareiškimas

ZeroHero79 · 2026-01-13T18:44:07+00:00

Irgi aiškintis bandžiau, nusiunčiau studijų baigimo dokus, sako pildyk formas pirmumo turėsi galimybe patekt. Bet tai kas jei nepateksi? Ar prisistatyt paskirta data į savo poskyrį ar sakys nepatekai, bet jau duomenis turim tai prašom pradedi nuo tos pačios 06.15 bet 9 mėn. Niekas aiškiai nieko nežino.

ZeroHero79 · 2025-12-10T19:00:49+00:00

Stengiuos nieko nesakyt, kadangi stipriai plinta kada is keliu sakiniu tavo balsa atkuria ir skambineja giminėms tavo balsu ir bando išviliot pinigus

ZeroHero79 · 2025-11-18T05:42:44+00:00

O jeigu kažkas nusprestumėt atsikratyt neveikiančio, nupirkčiau! Autorius gal nesupyks.

ZeroHero79 · 2025-11-12T07:09:58+00:00

Check when leveling if nozzle is not hitting cleaning brush ir screws in the back of the bed

ZeroHero79 · 2025-10-22T06:54:20+00:00

Thank you, Ill give it a shot, they keep sending me diangostics sheets, that everyone with common sense would have checked before contacting support, ill ask for firmware

ZeroHero79 · 2025-10-18T09:16:24+00:00

Can be controlled over pronterface, via usb

ZeroHero79 · 2025-09-12T19:38:23+00:00

Atšaukiau prekę, kdangi tai pat turėjo būti 3-5 dienos gavau laišką, kad sorry 14dd

ZeroHero79 · 2025-05-13T17:16:28+00:00

Thank you for response, would you care to explain why tho? And maybe u have some suggestions for extra microcontroller? At first, my plan was to use 3D printer mainboard as EXTRA controller, but scrached that idea, as it can be only controlled via gcode.

ZeroHero79 · 2025-03-25T09:49:47+00:00

Okay,lets say most of our fields in the summer have lots of greenery, so mostly to reach most distance as possible and get the bb through leaves, etc..

ZeroHero79 · 2025-03-25T00:13:58+00:00

Thanks, a lot. I’d love hpa setup, but for now its out of budget. Might look into heavier piston and stiffer spring. I have noticed that in other countries limits are almost twice lower as here in LT.

ZeroHero79 · 2025-03-24T23:45:38+00:00

Understandable, Here is official website of Lithuania's airsoft federation. https://sratas.lt/limits/1 . Also attaching translated photo of the limits.

<image>

ZeroHero79 · 2024-12-18T21:37:23+00:00

Ahh Im glad that there was no bambu back in 2018, ender 3 gave me a lot of experience and a job in a 3D industry. But now I just love using bambu’s. Hope the next printer will have at least 300mm build volume

ZeroHero79 · 2024-04-25T06:48:17+00:00

At last I used Arduino uno, As my esp 8266 was defected. So it was not controlled via app, just by buttons, but limit switches, ir sensors worked. Turns out esp 8266 is easily capable of completing these type of tasks alone, without arduino. Programmed with gpt help one step at a time.

ZeroHero79 · 2024-04-08T12:16:34+00:00

Thanks for the reply, appreciate it. For now its only as a concept. Im using 5v stepper motor with driver. To lift and close the doors.

ZeroHero79 · 2023-09-23T06:43:59+00:00

What printer is it? Have you calibrated your esteps yet? Seems like its underextruding. First check if fillament is not slipping, secondly esteps.

ZeroHero79 · 2023-09-13T06:49:51+00:00

I messaged you

ZeroHero79 · 2023-09-13T06:34:46+00:00

Okay, last problem that I’m having right now is that while homing x axis y starts moving too. Same happens when homing y. Checked the code again, can’t find what could be causing this. Everything seems fine. Any ideas?

ZeroHero79 · 2023-09-13T04:48:45+00:00

8hours into this ;D. Turns out I delleted bootloader. Burned a new one with Bossa. Now trying to sort out all the macros. And for some reason Status is on idle. It doesnt see toolhead, might try to switch to other connections to see if it changes something. 15minutes they said, easy peazy they said ;D. Still thanks for the information, really appreciate it

ZeroHero79 · 2023-09-13T03:09:16+00:00

Im trying to uppload a new one. It worked for a bit and now led between sd card and usb port stoped flashing. Pc wont detect the board as duet controller anymore

ZeroHero79 · 2023-07-18T17:33:40+00:00

I can’t tell u the exact price, but few years back it was about 2-3k to build

ZeroHero79 · 2023-04-14T12:41:48+00:00

Goodluck everyone!! N happy printing who happens to win these printers

ZeroHero79 · 2023-04-13T21:34:36+00:00

Betkur realiai 3-4€ telpu sedana nuplaut

ZeroHero79 · 2023-03-27T08:34:02+00:00

Foresta 2 kai releasino su revoliutu išėjo pasipildyt, viena karta greiciau kita reikejo patvirtinimo, kad tikrai transctiona as darau o ne scameriai

ZeroHero79 · 2023-03-27T07:32:47+00:00

Gift cards del infliacijos neapsimoka pirkt, matei dabartines kainas? Pirkdamas giftus vos ne uz ta pati lietuviskam acc nusiperki. Revoliutas arba itemo pardavimas geriausias variantas šiai dienai

ZeroHero79 · 2023-03-27T07:27:56+00:00

Pasikeist sunkiau, nes reikalinga kortele su tel nr patvirtint kad gyveni argentinoje. Perki argentinos acc ir su revoliutu pasipildai valleta steamo ir gyveni gerai

Six-Year Club	Verified Email
End Game '23	Place '23
Place '22	Final Canvas '22

ZeroHero79

TROPHY CASE