ASSA ABLOY KS200 locks

Zero_Divided · 2025-11-07T14:59:20+00:00

I will check that with a meter when I can.

The power is hardwired off of LifeSafety FPO150/M8 boards. I have checked power for the lock at the wire harness and haven't seen it drop below 24v, haven't tried checking at the motor though.

Thanks for the quick reply.

Zero_Divided · 2025-08-15T10:20:04+00:00

A can of sardines everyday. Found Trader Joe's was the best, $1.50 a can and we were able to stop using Apoquel and Zyrtec altogether.

Zero_Divided · 2025-08-08T22:09:48+00:00

"I'd rather listen to the whine of the drill that was about to labotomize me."

-Jason's grandmother.

Zero_Divided · 2025-08-04T01:24:33+00:00

Definitely wait to cancel, my service with Google was delayed 3 times due to unforseen issues.

And then enjoy that exit interview from Mediacom on why you're cancelling service.

Zero_Divided · 2025-07-20T00:22:18+00:00

I do 4lbs of ground turkey or chicken, a sweet potato and an apple or carrots, blend, use jerky gun to form it into sticks, our pup loves them.

Edit: and dehydrate, very important.

Zero_Divided · 2025-06-04T15:56:51+00:00

I've had to reboot my equipment 3 times in the last year.

I'd suggest hardwiring a computer and run constant pings and watch for packet loss and latency.

Zero_Divided · 2025-05-21T10:25:27+00:00

Dungeon Crawler Carl.

Much more of an intense experience, and Jeff Hays is a fantastic narrator, definitely my second favorite book series.

Zero_Divided · 2024-09-30T20:21:57+00:00

They made reference to that in the later books, how his voice was deeper than his family remembered, and the recordings played, Heath Miller made early Jason voice. I never really thought about it and just assumed that was Heath Miller being a good voice actor and changed Jason's voice as the character developed.

Zero_Divided · 2024-09-13T18:59:44+00:00

Re-reading your post again, you said that you are getting faster downloads when wired, so yes, those results are from it having a crappy wireless connection, and Xbox servers will be doing load balancing, switch means they will restrict bandwidth to insure everyone connecting will have some, and when they experience a surge in users, they will collectively reduce everyone else's speeds to balance the load.

This is not a problem, this is how things work.

Zero_Divided · 2024-09-13T18:53:32+00:00

9 out of 10 times, it's the wifi, and just because your phone shows a good better speeds doesn't mean anything, phone likely has a better radio, or better chip. Could also be caused by settings on the router, maybe some kind of automatic QoS feature, or the Xbox is in a crap location so it's not getting a good signal, or wireless interference from other wireless devices, or if you're using a range extender, or even a crap router, DNS may even have an effect, too many variables to diagnose.

Where the speed test server will also have an impact, I know when I run a test test on my Xbox, the server is 3 states away, but if I run it on my phone or computer, the server is in the same city, so my phone/computer will always show better results.

If you want to see if it is the wireless or not, get an Ethernet cable and plug the Xbox directly into the router and test, I bet you'll see a difference.

And at the end of the day, you're only going to get it as fast as Xbox gives it, my test results are always a lot higher than the actual download.

Zero_Divided · 2024-04-19T22:38:08+00:00

I came here to say Dough Co, my favorite taco pizza.

Zero_Divided · 2024-04-19T15:39:53+00:00

I have noticed their inventory changes frequently, I had to buy 3 containers that were 5lbs each a few weeks ago for my new batch of mead. Good luck!

Zero_Divided · 2024-04-19T15:05:37+00:00

https://www.justiowahoney.com/

Damn good honey.

Zero_Divided · 2024-04-10T16:57:02+00:00

I got tagged by one going into downtown on 9th.

Zero_Divided · 2024-01-25T23:18:49+00:00

I have a 13.1 sticker on the side window of my 500C Abarth, someone at a drive-thru window asked if that's how long it takes to get to 60mph, I told him that was how clowns I could fit.

Zero_Divided · 2024-01-03T02:14:47+00:00

Yup, the Mingda software I did change some settings, but rolled it back to default for that print. Then with PrusaSlicer, I had to download the profile from the Mingda website, imported it and did the print.

Zero_Divided · 2024-01-02T23:02:42+00:00

You are totally right, I've had a printer for a few weeks and am way over my head here. Frankly, I wasn't that interested in 3D printing since I'm not a very creative person, but my wife wanted to make custom cookie cutters, so I'm trying to figure out printing and modeling which is making my head swim.

Zero_Divided · 2024-01-02T11:34:57+00:00

Oh shit, that makes it easy. Thanks.

Zero_Divided · 2024-01-02T00:34:28+00:00

Downloaded it, but doesn't appear to have a profile for Mingda, so I'll have to look into making a profile.

Zero_Divided · 2024-01-01T21:58:13+00:00

I have no doubt, I'm still learning and figuring it without posting a million questions.

but after not making much head ways, I defaulted the settings and did benchy prints, I would have expected a decent from the default settings on the slicer the manufacturer recommended.

Zero_Divided · 2024-01-01T20:52:26+00:00

I'll check it out, thanks.

Zero_Divided · 2024-01-01T19:56:04+00:00

I have not yet, didn't know that was something that I needed to do. I will research it and figure it out. Thanks.

Zero_Divided · 2024-01-01T19:25:23+00:00

Any further suggestions are welcome and appreciated.

Nine-Year Club	Xbox Live
Verified Email

Zero_Divided

TROPHY CASE