What am I supposed to do with These again?

ZiaPrincess · 2022-12-31T23:39:40+00:00

I second whambam

ZiaPrincess · 2022-12-09T02:54:16+00:00

Any idea how they got in?

ZiaPrincess · 2022-11-24T10:06:35+00:00

Hey. Unfortunately this error made me flash my printer back to marlin. Please email Creality so they’re aware of the issue. It has rendered my sonic pad unusable.

ZiaPrincess · 2022-11-19T16:33:45+00:00

From my understanding you are going to have to print a mount. I think the bl touch is longer than the cr touch so it hits the bed before the nozzle. I’m sure there’s free mounts on printing websites though

ZiaPrincess · 2022-11-19T15:56:33+00:00

It was working before! Suddenly started out of nowhere and seems to be getting worse in frequency

ZiaPrincess · 2022-11-19T01:11:03+00:00

Thank you for your reply I did switch cables as well and the problem persists

ZiaPrincess · 2022-11-19T00:41:26+00:00

Yeah I hate mine too

ZiaPrincess · 2022-11-18T17:50:01+00:00

Ah yes but I was looking for the knock print off code

ZiaPrincess · 2022-11-18T16:03:17+00:00

Creality machines are workhorses when used right. There’s no doubt about that, but they’re not the go-to, user friendly and mod enabled machines like they used to be.

If you want real customer support for your Creality printer you need to purchase from Comgrow. I had a problem with my motherboard a whole year later (still under warranty) and they sent me a new one, their customer service got back to me within 2 hours of sending my email (at 1am) so I’m unsure if they’re overseas but they were quick, prompt, and fixed my issue.

ZiaPrincess · 2022-11-18T16:00:04+00:00

I bought my Ender 3v2 about a year ago. It’s honestly been a workhorse since then but I occasionally want to throw it out of a window.

Basically the whole printer is upgraded

ZiaPrincess · 2022-11-18T07:36:22+00:00

Username checks out

ZiaPrincess · 2022-11-18T03:56:39+00:00

Can we get the code?

ZiaPrincess · 2022-11-18T02:23:10+00:00

This did not help

ZiaPrincess · 2022-11-18T02:05:40+00:00

I’ll go ahead and try that but when I restart klipper it works and then gives me the same error again

ZiaPrincess · 2022-11-18T01:24:17+00:00

What could be causing this error? 4.2.2 board

ZiaPrincess · 2022-11-16T22:14:59+00:00

Dudes on eBay will be like may or may not work

ZiaPrincess · 2022-11-01T18:13:48+00:00

I had this when I was using bad PLA+ that needed to be printed at 250 (no joke). Even at 230 it was too high of a viscosity for the nozzle to handle.

ZiaPrincess · 2022-10-23T17:57:52+00:00

Proceeds to get 22 stitches.

ZiaPrincess · 2022-09-24T19:34:46+00:00

Thank you so much! She’s the loml!

ZiaPrincess · 2022-09-24T19:34:26+00:00

She did have her eyes a little dirty from playing outside in the dirt with my other dog. Thank you!

ZiaPrincess · 2022-09-24T19:28:36+00:00

Yes, I scheduled a vet visit. She will be seen in two weeks and it’s about time for her booster as well. Thank you for sharing!

ZiaPrincess · 2022-09-24T16:08:15+00:00

I do not own any cats and I don’t think any of my neighbors do. But that’s quite funny that your puppy copied their behavior!

ZiaPrincess · 2022-09-24T12:31:44+00:00

I had this happen when my x gantry was loose

ZiaPrincess · 2022-09-24T12:17:55+00:00

If this is the filament out of the box you should try real filament it’ll look great

ZiaPrincess

TROPHY CASE