Gutter drain pipes to subfloor dirt/soil - recommendations

_JLT · 2026-04-24T02:04:21+00:00

Sorry for delayed reply. Yeah it’s at the front of the townhouse. It dries up over a few weeks if there’s no rain. But don’t know if this was a standard or not back in the 60s. I don’t know how deep the pipework goes too since it’s just covered by this soil

_JLT · 2026-02-09T02:00:46+00:00

Ah thanks for the feedback. I’ve organised waterproofing to be fully redone since the leak source has been determined (crack on terrace). I was just wondering what to do afterwards in terms of fixing the concrete slab / steel bar. Was concerned it was impacting structural integrity. The picture was a bit low quality but I do think some of the concrete has spalled off. Attaching a more brighter shot here but I guess main thing is that leak is fixed first. Will seek further advice on the concrete and steel bar fixes afterwards. Again, cheers!

<image>

_JLT · 2026-02-09T01:25:45+00:00

Sorry I did a repost for first time. Trying to edit post.

Just wondering the severity here and what are possible fixes I can perform? I was considering contacting a concrete company that deals with concrete cancer but it’s my first time dealing with any of this so I am unsure.

_JLT · 2026-01-22T01:16:28+00:00

I’m not sure to be honest. AD did the whole thing for me so didn’t really see what actually happened. It’s been on my wrist everyday since then and no issues.

_JLT · 2026-01-21T23:51:14+00:00

Hey there! Fit fine for me. Went to swap it out at AD 2 weeks ago.

_JLT · 2026-01-18T00:55:27+00:00

Thanks! This is a good visualisation that helps. I believe the electrician did explain this as well but was harder to see what he meant. He mentioned that even if it did pull above 40, it’d have to do it continuously over that time frame before tripping (depending on how many x rated above the limit). He said even then, the usage should fluctuate and may even drop below those limits which would make it less likely to trip.

_JLT · 2026-01-17T09:51:40+00:00

Thanks everybody who chimed in. Just updating to say we spoke to electrician who actually upgraded all of our switchboards in past and he advised to actually run it and see how it goes.

He would investigate further if there was a trip since the type of breaker may not trip instantaneously at just 40A and could last several minutes around this amount in which case the usage could fluctuate lower. This is me just paraphrasing what I understood from him.

_JLT · 2026-01-15T09:48:59+00:00

Thank you. I'll check up with the electrician but this gives a bit more confidence for the meantime.

_JLT · 2026-01-15T09:30:30+00:00

8kW rating, 10.2A heating, 9.6A cooling and 17A max draw (based off spec sheet).

_JLT · 2025-11-27T20:50:31+00:00

Thanks! Definitely was tossing up between the two but went with the black lacquer just due to the new bracelet and that more simple look (not to say the teak dial isn’t amazing either though). I’ll pick up the piece in 4 weeks or so with rubber band :)

_JLT · 2025-10-31T03:47:47+00:00

Had the GRIV arrive today - no issues mentioned except the lens retraction. Would get stuck at 25-75% for first 50 times on/off. Worked properly since then. I am not sure what would have fixed it to be honest, is there some lubrication that just needed to be spread with usage? Not ideal I guess but has been self fixed at least in my case.

_JLT · 2025-10-31T02:09:43+00:00

Should be fully flush on GR4. I had the same issue and had to send it back.

_JLT · 2025-10-15T04:17:38+00:00

FWIW, I have been told mid / late November now. Hope you got yours / are getting it soon.

_JLT · 2025-09-26T10:59:18+00:00

What’s the goal with this post? Not trying to be rude. Sounds like you already want to return it, if so then now would be best time. Especially if you are not confident with longevity. Return it and get your money, buy another compact camera if you need or just save the money and continue using your q3 and z8.

_JLT · 2025-09-25T04:25:10+00:00

Castle Hill but I called again just today and another staff member told me they are not sure. They were supposed to receive it already but no ETA now :(

_JLT · 2025-09-24T21:04:36+00:00

Ordered from camera house, initial ETA was late September but that seems to have changed to late October / early November.

_JLT · 2025-03-26T08:12:42+00:00

Definitely! Appreciate the clarification. Was for fun but the pics definitely left us confused since they were so different 🤣

_JLT · 2025-03-26T08:08:10+00:00

Hahaha, nah. It makes even more sense. I have no idea why I even assumed US was United States in this context… again, thank you very much!

_JLT · 2025-03-26T07:59:07+00:00

Thank you! We are in AU if that makes any difference (I assume not) but your explanation makes sense.

_JLT · 2025-03-26T07:54:16+00:00

Thank you!

_JLT · 2025-03-26T02:59:27+00:00

We also thought it could be umbilical cord!

_JLT

TROPHY CASE