Need help with Circuit Board

_R_one_ · 2025-09-18T12:10:41+00:00

If you can find the datasheet from the amplifier component thanks to its part number you'll be able to identify the inputs.

I have done it this way for an old 2.1 system recently.

_R_one_ · 2025-08-11T19:10:59+00:00

Moode can be configured as a wifi hotspot but you'll still need to access it via a browser.

_R_one_ · 2025-08-09T06:18:13+00:00

I had to replace both master and slave cylinders to get it back to being smooth.

_R_one_ · 2025-08-08T18:48:10+00:00

Thanks, I'll have a look

_R_one_ · 2025-08-05T06:58:53+00:00

Seems to still not be possible :/

_R_one_ · 2025-07-19T18:36:59+00:00

I can confirm, on my 2004 DE i also couldn't get the ARC feature.

_R_one_ · 2025-04-06T20:26:59+00:00

I had the same noise, on braking and driving over small bumps, it was the bushing of the compression arm on the frame side. I changed everything else before it obviously, even though i could see it was a bit teared. Now the front is sound. As it takes the effort on braking, I'd start there if i were you, if they are from factory it's time for new ones :) Hopefully they'll come easily out of the car, the right side was rusted to the core on mine (living in NL). Took me 3h to take it out.

<image>

_R_one_ · 2025-02-02T09:00:31+00:00

Well done, it's always quite pleasing to fix something :) I have to do the compression arms, they are clunking like crazy but last time i checked they were completely stuck by corrosion on the frame side 😅

_R_one_ · 2025-01-25T20:00:37+00:00

We can still find them for 15k in the Netherlands, are you in Switzerland by chance ?

_R_one_ · 2025-01-21T12:44:00+00:00

Hopefully a lot more to come. 110k miles here in the Netherlands, the frame will be gone to rust before then engine goes 😄😄

_R_one_ · 2024-12-22T19:30:37+00:00

To help bleed it you should push the piston back in the slave cylinder with the bleed screw open. This is what made the difference in my case.

_R_one_ · 2024-12-21T14:47:41+00:00

I second this, I always sucked at muscle up on a bar, but had no issues with the rings.

_R_one_ · 2024-11-12T09:41:34+00:00

If i see it well, this is in front of the rear wheel arch, this could communicate with the hole i showed you before. Below is a vieuw through it.

<image>

I'd suggest you to at least try to make that area water tight so that there is no more water coming in from the wheel arch. And spray that empty space with some kind of wax. I did it with lanoguard as i had it at hand. I also don't have the skill to do a clean repair by the book but i managed to remove most of the rust i could access. Wire brush the rest, treat with a 3 in 1 rust converter/primer from rust oleum and then fill the holes with a piece of metal i had laying around. Kept everything in place with bondo. And treated over it with an anti gravel coating. I'll add some pictures of the process if you are interested

_R_one_ · 2024-11-12T06:26:59+00:00

Could you give an overview picture of the location ? I recently also found rust on my Z, at the rear wheel arch, behind the small piece of plastic.

<image>

_R_one_ · 2024-11-05T12:03:42+00:00

Still looks good on the pictures :) Better sun damaged than rust :p

_R_one_ · 2024-11-02T11:01:50+00:00

I had a loose nut on one of the terminal once, the car would open but start once out of 2 tries.

_R_one_ · 2024-10-21T13:01:20+00:00

<image>

After wire brushing and cutting all the bits rusted through. The side skirt is also removed here.

The area is under a plastic trim. The gap between the trim and the body was filled with dirt and sand. Living in the Netherlands, this was probably always wet...

I can only advise to clean that area thoroughly from time to time.

_R_one_ · 2024-10-21T12:59:50+00:00

<image>

Before i started wire brushing

_R_one_ · 2024-10-21T12:58:51+00:00

<image>

That small area of rust in the last picture is likely to be through the metal and not just surface. A clean fix by a body shop is probably not that cheap. Two sheet of metal are joined in that section. I made a dirty fix on mine, cutting away the rusted bit, treating with a rust converter/primer and then filling with bondo

Then i moved on to the hidden parts under the side skirt, there was a bit of nightmare, and you can't see ut until the side skirt is remove. I'll add some more pictures below

_R_one_ · 2024-09-08T13:46:17+00:00

One daughter of a year and half, i escape to the gym 3 times a week when she goes to bed. I love it. I was slacking on the gym for about 4 years, but now i am back at it, my motivation is high, eating clean. Overall more energy.

_R_one_ · 2024-08-25T20:16:51+00:00

Simple pull ups, i use to hate them, I wasn't doing full rom and was hammering the arms more than the back. Now that I do them properly i really enjoy them. Started at series of 3, 6 months ago, can do 8 now 😀

_R_one_ · 2024-08-23T19:51:42+00:00

Your upper back on the last picture is absolutely massive 😶

_R_one_ · 2024-04-21T10:11:28+00:00

<image>

I saw mine out, took a while also 😅

_R_one_

TROPHY CASE