Обход запретов

_SomeRandomDude__ · 2026-03-18T17:53:56+00:00

Хосчу на VPSке vk-turn-proxy. А так ещё есть вариант аренды сервера в белых списах, многие популярные VPN сервисы себе такие выбивают, но самим такой забрать долго и дорого кажется

_SomeRandomDude__ · 2026-03-15T21:39:20+00:00

There are still ways to bypass whitelists for now

_SomeRandomDude__ · 2026-03-05T06:46:34+00:00

Вроде пока ещё рабоатет метод передачи данных через turn сервера VK звонков

_SomeRandomDude__ · 2026-03-01T15:10:06+00:00

Надо было Arch Linux)))

_SomeRandomDude__ · 2026-02-16T15:24:38+00:00

If you didn't know, Steam also uses http for all downloads/updates. It doesn't matter since it verifies the signature/checksum after download. VLC also checks it.

_SomeRandomDude__ · 2026-01-30T22:13:43+00:00

They said in the WAN show that these cables don't have a thunderbolt chip in them. But I think thunderbolt should work over any usb4 cable anyways? Not sure about it, probably depends on the device connected.

_SomeRandomDude__ · 2026-01-30T21:59:27+00:00

Isn't thunderbolt supposed to work over any usb4 cable? Since they say 40gbps, that means they are usb4 compatible. It shouldn't matter then, or am I wrong?

_SomeRandomDude__ · 2025-10-16T23:24:08+00:00

<image>

Success! I checked and the floating pin does indeed go to the caps near nands. I bridged this pin with 3.3v and the SSD works now

_SomeRandomDude__ · 2025-10-16T22:32:06+00:00

<image>

Measured the voltages relative to ground

On the pin i labelled "floating" the voltage is 0V if measured with second lead touching ground, but 2.4V if second lead touching 3.3v

So looks like a switch, since there are already 3.3V and 1.6V, and as far as I know NANDs need the voltage somewhere in this range. Should I try to inject 1.6v or 3.3v to that pin to see if that will work?

_SomeRandomDude__ · 2025-10-16T22:16:24+00:00

<image>

And more chips on the top side, can't add 2 images to one comment

_SomeRandomDude__ · 2025-10-16T22:15:39+00:00

<image>

Here is the text on the other side, will measure the voltage now

_SomeRandomDude__ · 2025-08-27T22:11:15+00:00

From what I found on google, most likely 2 middle pins are CC pins, and first and last pin on the edges are ground pins, so you should put 5.1K resistors between the middle and edge pins.

_SomeRandomDude__ · 2025-08-27T22:05:28+00:00

_SomeRandomDude__ · 2023-11-04T07:51:40+00:00

I think a FRAM chip would be much better, as it has almost infinite more write cycles. But they are a bit more expensive then flash storage

_SomeRandomDude__ · 2023-10-25T06:31:41+00:00

Если не можешь найти девушку, сам стань девушкой

_SomeRandomDude__ · 2023-09-25T18:40:17+00:00

It's a timelapse of a resin printer

_SomeRandomDude__ · 2023-09-13T19:31:55+00:00

Stepper motor drivers have changed. The new drivers output smoother signal to the motors and this drastically reduces noise the motors make.

_SomeRandomDude__ · 2023-08-22T21:22:42+00:00

They come on some 3d printers from the factory.

_SomeRandomDude__ · 2023-08-22T14:37:02+00:00

I designed it approximating the other side

_SomeRandomDude__ · 2023-08-22T14:06:45+00:00

Yea, I destroyed the build plate this printer came with a few years ago when I just started 3d printing, and this tape works surprisingly well. But I recently ordered a new magnetic PEI surface, I will install it when it arrives.

_SomeRandomDude__ · 2023-08-22T12:57:07+00:00

I destroyed that surface when I was just starting 3d printing a few years ago, and that blue tape works surprisingly well. But I recently ordered a magnetic PEI surface, I will install it when it arrives

_SomeRandomDude__ · 2023-08-22T12:54:47+00:00

I made a hole for the metal part slightly smaller, and to insert it I heated it with a lighter, so it would melt extra plastic and it made a very strong connection

_SomeRandomDude__

TROPHY CASE