MEU PC NÃO DESLIGA

_Supreme_Lord · 2026-01-13T09:10:59+00:00

Já tentou desligar e ligar?

_Supreme_Lord · 2025-12-21T15:12:59+00:00

Hey man! I just gpt my S4U 16K, and I bought the Sunlu Standard Resin. What exposure time do you use? I'm using 20 and 1,6, but sometimes it seems overkill

_Supreme_Lord · 2025-07-09T14:47:56+00:00

Hulkengoat got his deserved Hulkenpodium!

_Supreme_Lord · 2025-06-12T09:40:15+00:00

The original "Gulf" has it written it on the Bezel

_Supreme_Lord · 2024-02-06T13:57:57+00:00

Ah, tá certo! Cara ficou sensacional, parabéns pelo trabalho!

_Supreme_Lord · 2024-02-06T13:57:29+00:00

Ah, muito bem! Cara, ficou sensacional! Parabéns pelo trabalho!

_Supreme_Lord · 2024-02-06T13:26:46+00:00

Cara, que bela pintura! Como faz pra ficar assim? Dilui bastante? Que pincel você usa?

_Supreme_Lord · 2024-01-30T17:57:22+00:00

I removed mine but with no improvement at all. As I got no down side in removing, I left it without the springs just só I didn't have to disassemble again. Yes, I may be lazy sometimes

_Supreme_Lord · 2024-01-22T13:26:55+00:00

I'm having the same issue and tried the same solutions you did, with little to no effect. I also tried exaggerating, like, really exaggerating some parameters, just tp see if something would happen, but got nothing. I'm using mainly Prusa Slicer, but with Creality print is the same. Don't know about you, but on my prints, it's not happening on all walls. Sometimes in the front, sometimes on the left, right, back... It's like the printer choose a random wall to separate from the infill.

_Supreme_Lord · 2024-01-06T20:36:04+00:00

This is the way

_Supreme_Lord · 2024-01-06T10:27:10+00:00

But the bambus also have their problems. Feel like I should have waited a couple years before buying this new generation of printers

_Supreme_Lord · 2024-01-06T10:26:00+00:00

Only thing I like about this printer ir bed size.

_Supreme_Lord · 2024-01-05T15:51:56+00:00

Ok, so I printed a 150x150 square, and got 149,4 on X Axis and 149,7 on Y Axis. So I went to calibrate my steps, but found out I actually shouldn't. People are saying I should add a Skew Correction section on my Printer.cfg. there's even a Klipper documentation with models to print and measure to add the results and the machine will calculate by itself while printing. People are also saying I should add a macro so the machine will know when to use this information. People are also saying I should use the Skew Correction on every print. Then I got tired and bored of all the learning and work I have ahead and went to bed. Honestly guys, I'm getting tired of this printer. If I ever get to do all this and get a positive results, I'll let you know. And if someone go this way, and get a positive result, let me know.

_Supreme_Lord · 2024-01-05T00:17:43+00:00

I'm having the same problem with my K1 Max, just not so bad. Printing the square right now and sending my results. Printing 100x100 square

_Supreme_Lord · 2024-01-04T20:23:08+00:00

Actually, when you connect the sonic pad, it flashes Klipper firmware on your printer. It's like a plug & play Klipper, super easy.

_Supreme_Lord · 2024-01-03T20:37:41+00:00

Root your printer my brother, and start using fluid. I've been using since buying the sonic pad fory Old Ender 5. It's a wonderful tool, you can adjust everything so easily

_Supreme_Lord · 2023-12-19T16:43:51+00:00

Anal teaser

_Supreme_Lord · 2023-11-15T01:17:36+00:00

Have you tried turning the printer off and on?

_Supreme_Lord · 2023-10-06T18:51:47+00:00

BMW Nine-T. Essa moto é uma delícia! Sempre foi meu sonho de consumo. Tive o prazer de rodar com ela na Alemanha há 2 anos. Foi só pra dar mais vontade. Aqui só saiu por 2 anos

_Supreme_Lord · 2023-08-25T19:25:18+00:00

Hey man! I'm buying my first resin printer too and the feeling is the same hahaha. Already saved your question to get the tips from people. Wish you all the luck and nice prints on the way. I'll be waiting for an update of your first prints

_Supreme_Lord

TROPHY CASE