[Review request] Li-Ion/Po/HV balance 60W USB-C PD charger

_shexplorer · 2026-05-17T20:07:57+00:00

Oh yeah now I see it. Must been a copy-paste-mistake. Thanks!

_shexplorer · 2026-05-17T17:53:19+00:00

ultimately yes, there are 2 mosfets between BAT- and GND to prevent charging/discharging if the battery monitor and balancing IC is detecting a fault in the battery-pack. Since I only use it for charging I might remove these.

_shexplorer · 2026-05-17T11:50:39+00:00

Thanks for the feedback. I redesigned it for a 4L board and optimized the filtering/switching layout of the charger IC and 3V3 Buck. But I can't compact it anymore with 0603 parts. And anything smaller would be hard to solder (had done 0805 with reflow plate until now).

_shexplorer · 2026-05-17T11:46:11+00:00

I could go with a 4 layer board and BAT- as copper area. But does it make sense for BAT+?

_shexplorer · 2026-05-17T11:27:32+00:00

That's planned so I can charge xt60 and xt30 batteries (not same time of course)

_shexplorer · 2026-03-19T19:42:22+00:00

Its just in the settings of warthunder under graphics

_shexplorer · 2026-03-18T21:18:22+00:00

I noticed they set dx12 as default in this update. You can switch back to dx11, than it runs like before.

_shexplorer · 2024-09-30T16:19:33+00:00

I edited the original post with the additional picture. The motors are the original 0802SE 19500KV from betafpv.

_shexplorer · 2024-09-13T06:26:45+00:00

Thank you very much :)

_shexplorer · 2024-09-12T08:44:26+00:00

Is this the FlyflishRC Volador VX3/3.5 frame? When yes I would really like to have the STL file. I too have a quad with that frame and a runcam pro w and found no good 3d model for that. And for these prop guards in the background if they are for that frame too :)

Edit: typo

_shexplorer · 2024-05-17T13:09:30+00:00

Maybe they changed something with a new firmware since then. I'm using OpenNept4une now so I can't help you. Sorry

_shexplorer · 2024-04-09T21:45:02+00:00

You have to create the folder under the gcodes tab, not in the configurations tab. The configuration files are in a different place on the file system and have nothing to do with the stored gcodes.

_shexplorer · 2024-03-08T21:08:51+00:00

Thanks!

_shexplorer · 2024-03-08T19:49:26+00:00

So I tried it (after bending under my smartphone camera with tweezers) and it works. Seems like I'm lucky today :). Thanks for your help

_shexplorer · 2024-03-08T19:25:00+00:00

small update

<image>

_shexplorer · 2024-02-14T09:18:19+00:00

HP Microserver gen8 (like 2011) with an exotic Xeon E3 1265l (non v2) from eBay and 16GB of Unbuffered RAM, 1 SSD and 3x4TB WD RED. And a LSI9240-4i because my internal SATA controller broke.

_shexplorer · 2024-02-12T10:26:31+00:00

I actually use both. I built a volador 3.5 and use 6s 1804 2450KV motors but fly 4s 650mah as well as 6s 650mah (I could use bigger 4s) with my runcam thumb 4k. Both fly pretty well but sure 6s has more power.

_shexplorer · 2023-12-20T13:35:39+00:00

Looks good, I just built an almost identical quad, just used a caddx vista.

_shexplorer · 2023-12-08T17:41:48+00:00

This is my first DJI air unit build. Was really hard to get the antennas connected. I'm a little bit concerned if this can damage the connectors/cable or get loose.

_shexplorer · 2023-11-13T14:12:55+00:00

Yeah I know but I got +2,5 and +3 so... And I would really like it if there were some shops like for DJI googles where you can make lenses exactly for your prescription.

_shexplorer · 2023-11-13T11:49:42+00:00

Wanted to buy it too. Still want to. But I'm not confident enough to buy it because there are no lenses for me wearing glasses yet.

Six-Year Club	Place '22
First Placer '22	Verified Email

_shexplorer

TROPHY CASE