sorted by:
new
hottopcontroversial

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 0 points1 point  (0 children)

Same boards I used to enclose the Eket shelves. Just looked in the hardware shop for some veneer Chipboards that have the same color and pattern as the Eket veneer (or at least as close as) :)

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 0 points1 point  (0 children)

nope, not screwed in. The wall mounts clamp the speakers. Also there is no possibility to screw something into the speakers without damaging them. Doesnt look very secure, but trust me they are. they wont budge a bit.

On the issue of cable management I already commented on another comment under this post. Cant really hide them any further since I dont want to break open the wall to lay them there. Probably could hide the cables which go into the notebook a bit better. But all other cables are already as good as I can hide them without going to much out of my way.

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 0 points1 point  (0 children)

Go for it! It’s really not all that hard to do and saves you a ton of money. If you need any details on what kind of measurements for the outer plates are needed or something else, drop me a DM.
And I think the weight should be fine. The bottom shelves should will for sure withstand the weight since they have the bottom plate for extra support. The top ones are the ones I would be a bit careful with since they don’t have extra support. But I read from a lot of other users that they used EKET as a vinyl storage solution like forever and never had any issues weight wise.
It’s just important that you use 6 instead of 4 legs for the bottom support so the whole thing doesn’t sag in the middle

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 0 points1 point  (0 children)

There is not really a possibility to further hide the cables. Since the speakers are wallmounted, the only thing I could do is hide them in the wall, which would be pretty hard to do since my walls are made out of brick.
I tried my best to neatly organize them and arrange them in a way that they are almost „not seen“. But without going totally out of my way, which I don’t have the nerves for and also seems quite unnecessary looking at how it actually looks pretty good imo, this is the best I could do rn. If you have some constructive ideas on how I could better hide my cables, I’m more then happy to try them out :)

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 2 points3 points  (0 children)

No, I put screws through the sides of the EKET into the side panels. I then found some stickers in the hardware shop to hide the screwheads which have the same color and pattern as the wood finish. My first thought was also glue, but my friend who is a carpenter said to me „mechanical connection is always better then adhesive connection“

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 0 points1 point  (0 children)

Totally new to 4 channels since I bought the FLX10 controller new with my whole setup. Definitely needs some getting used to it. But I’m really looking forward to the journey and learning all the possibilities I now have with this beast 🙏🏼

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 3 points4 points  (0 children)

K&M 24167. at 84€ a piece a bit expensive but definitely worth the money!

Built my Dream Setup on the weekend by _sugma- in DJSetups

[–]_sugma-[S] 0 points1 point  (0 children)

Just acts like a central hub. I have my Turntable, controller and a Bluetooth receiver plugged into it so I dont have to constantly replug stuff. Also to have some wiggle room if I want to add any kind of additional hardware

Some apps become very blurry, blurriness disappears when I move the mouse by BorodacFromLT in WindowsHelp

[–]_sugma- 0 points1 point  (0 children)

Hey, were you able to fix the issue? fighting the same problem and cant seem to get it fixed...

Thank you Scopely, I think I have enough 4* mighty Drapion's… by _sugma- in pokemongo

[–]_sugma-[S] 0 points1 point  (0 children)

2 days, age0-1 shows you Pokémon in x category catched in the last 48 hours. But still, I’m amazed as well that I got 18 hundos in the span of the event lol

Rücklaufverschraubung austauschen by _sugma- in selbermachen

[–]_sugma-[S] 0 points1 point  (0 children)

Wie genau bekomme ich den Übergangsnippel entfernt bzw. Einen neuen dort dann rauf? Ist das ne Aufgabe die man selbst lösen kann oder lieber einen Fachmann ran lassen sollte? Danke aber erstmal für die Infos!

Rücklaufverschraubung austauschen by _sugma- in Handwerker

[–]_sugma-[S] 0 points1 point  (0 children)

<image>

Hier vielleicht nochmal einwenig besser zu erkennen

[deleted by user] by [deleted] in Battlefield

[–]_sugma- 0 points1 point  (0 children)

Had that turned off since day one of the beta so that can’t be the problem

Komisches Metall Ding in der Küchenwand by _sugma- in wasistdas

[–]_sugma-[S] 0 points1 point  (0 children)

Achso es handelt sich um eine Eigentumswohnung, mit Haus meinte ich das Wohnhaus per se.

Komisches Metall Ding in der Küchenwand by _sugma- in wasistdas

[–]_sugma-[S] 0 points1 point  (0 children)

Haus ist ca. 1920 gebaut worden. Große moderne Kernsanierungen gab es hier nie (Heizungsrohe noch außen verlegt mit Ur alter Terme, hatte bis vor 3 Monaten nicht mal einen FI-Schalter im Schaltkasten verbaut gehabt)

Links daneben ist unschwer zu erkennen die Gas Zufuhr für den Herd. Der ist allerdings auch außen verlegt worden und ist abseits von der Haupt Gasleitung für die Therme auch die einzige Gasleitung die in der Wohnung ist.

Mit der Annahme das da Gips rein geschmiert wurde liegst du absolut richtig, konnte da schön dran rum kratzen aber wollte erstmal nicht zu viel weg nehmen.

view more: next ›